Trailer Door Parts

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

Good question, Tina - you’re in the safe zone with the M-3 aluminum plate #M348FR. It’s 3/16 inch thick and fully welded across the piano hinge (some cheaper ones are just bolted instead of welded), so even with heavy mowers or small tractors, it…

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

Hey Alan - you can absolutely use the M3 plate at the door-to-floor gap. Many folks run one on the outside edge and another inside for a totally smooth roll-through. The steel plate #M368FR gives you extra strength if you’re using pallet jacks or…

Hey Mike, thanks for reaching out. For the CTG60-2360W MORryde RV Cargo Slide Tray #MR87ZV, the 23" dimensions you see listed is the overall max width of the entire assembly. The inside dimension of the tray is approximately 19-7/8". For…

Hey Dylan - both M-3 plates measure 81-3/4 inches wide, so you'd need to trim off a little bit. The aluminum one #M348FR would be easier to trim, so I'd pick that over the steel one. The hinge runs the full width so you’ll still get solid…

Happy to help James, thanks for reaching out! Choosing the right M-3 ramp door spring system really comes down to matching your specific trailer and door. The biggest factor is the weight of your ramp door. The spring system is designed to help lift…

We have quite a few options Marvin! The Conventional Ramp Door Spring for 8' Wide Enclosed Trailer item #M386FR you were looking at, is designed for trailer doors 94-3/8"- 95-3/8" wide. It comes with all mounting hardware and brackets,…

Hey Robert, we have rubber lip seals for compartment doors on RVs with the part #SR92FR which is a 15 foot long section. Did yours fail over time or did it fall off?

Hey Bert, the biggest difference would be the Load Range which is a fancier way of saying the weight capacity. The Continental 235/75R17.5 HTR2 LRH has a Load Range of H whereas the Provider 235/75R17.5 LRJ is a Load Range J which means it has a…

Hey Dustin. I installed the Enclosed Trailer Transition Plate item #M368FR on a trailer here when we first got them in and you're good! That plate is single solid piece of steel. It's got a heavy duty piano style hinge that has been riveted…

Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…

Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…

Good question, Tina - you’re in the safe zone with the M-3 aluminum plate #M348FR. It’s 3/16 inch thick and fully welded across the piano hinge (some cheaper ones are just bolted instead of welded), so even with heavy mowers or small tractors, it…

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

Hey Alan - you can absolutely use the M3 plate at the door-to-floor gap. Many folks run one on the outside edge and another inside for a totally smooth roll-through. The steel plate #M368FR gives you extra strength if you’re using pallet jacks or…

Hey Mike, thanks for reaching out. For the CTG60-2360W MORryde RV Cargo Slide Tray #MR87ZV, the 23" dimensions you see listed is the overall max width of the entire assembly. The inside dimension of the tray is approximately 19-7/8". For…

Hey Dylan - both M-3 plates measure 81-3/4 inches wide, so you'd need to trim off a little bit. The aluminum one #M348FR would be easier to trim, so I'd pick that over the steel one. The hinge runs the full width so you’ll still get solid…

Happy to help James, thanks for reaching out! Choosing the right M-3 ramp door spring system really comes down to matching your specific trailer and door. The biggest factor is the weight of your ramp door. The spring system is designed to help lift…

We have quite a few options Marvin! The Conventional Ramp Door Spring for 8' Wide Enclosed Trailer item #M386FR you were looking at, is designed for trailer doors 94-3/8"- 95-3/8" wide. It comes with all mounting hardware and brackets,…

Hey Robert, we have rubber lip seals for compartment doors on RVs with the part #SR92FR which is a 15 foot long section. Did yours fail over time or did it fall off?

Hey Bert, the biggest difference would be the Load Range which is a fancier way of saying the weight capacity. The Continental 235/75R17.5 HTR2 LRH has a Load Range of H whereas the Provider 235/75R17.5 LRJ is a Load Range J which means it has a…

Hey Dustin. I installed the Enclosed Trailer Transition Plate item #M368FR on a trailer here when we first got them in and you're good! That plate is single solid piece of steel. It's got a heavy duty piano style hinge that has been riveted…

Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…