2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs

Ask the Experts about this Draw-Tite Hitch Ball
Do you have a question about this Hitch Ball?

• What Drawbar Length Should be Used on 2018 Subaru Crosstrek?
  
• The end of the receiver on Draw-Tite # 36644 is about even with the back of your 2018 Subaru Crosstrek, as you can see in the accompanying photo. So without having to worry about any clearance issue and Draw-Tite drawbars # 3592 and # 3593 are the same in every way except for length, the truth is neither of them are "better" and you will be fine with either option. Both drawbars come with a pin and clip, so the only other thing you'd need is a hitch ball, # 19256 for a 1-7/8" ball or #...
  view full answer...


• How to Carry 4 Bikes with a 2017 Chevrolet Volt
  
• It sounds like you're trying to carry four bikes on a 2017 Chevrolet Volt. I have a solution for you, but the Volt is limited to only 2 bikes on a hitch mount carrier and we do not have any fits for roof racks to carry bikes. The only option we have to carry all 4 bikes is to install a hitch receiver on the Volt and tow the Yakima Rack and Roll # Y08106 behind it carrying the bikes. The Rack and Roll is basically Yakima roof rack on wheels so it can be used to carry a variety of things...
  view full answer...


• Correct Wiring Kit for a 2019 Hyundai Santa Fe with the Trailer Tow Prep Package
  
• If your 2019 Hyundai Santa Fe has the tow package then you want to use the Tekonsha T-One # 118784 which has the 4-Way Flat connector that you asked about and plugs into the factory connector which is located under the vehicle, behind the rear bumper, on the driver’s side. You said that you already have the trailer hitch for towing but you didn't mention a ball mount kit. If your trailer hitch has a 2" receiver like the Curt # C13195 which fits a 2019 Santa Fe then I recommend the Curt...
  view full answer...


• Trailer Hitch and Wiring for a 2017 Volkswagen Golf SportWagen Alltrack
  
• The Alltrack is a version of the 2017 Volkswagen Golf SportWagen. Curt and Draw-Tite indicate that their hitches fit all models of the 2017 SportWagen. So I recommend Draw-Tite hitch # 24949 since it does not have special requirements for using a bike rack or cargo carrier like the Curt hitch does. The recommended ball mount for this hitch is # 3590. For a 1-7/8 inch ball use # 19257 and for a 2 inch use # 19258. The trailer wiring harness # 118730 is also listed as a fit for all models...
  view full answer...


• Will Fascia Still Line Up with Other Panels After Installing a Trailer Hitch on a 2018 Honda Accord
  
• Yes, the rear fascia will still line up with other panels after installation of Draw-Tite trailer hitch # 24972 on your 2018 Honda Accord. There is enough space in the stock set up to allow for the hitch to fit without compromising the fit of the fascia relative to the other panels. If you tow the recommended ball mount is # 3593 and you can use 1-7/8 inch ball # 19256 or 2 inch ball # 19258. For trailer wiring you can use # C56402 to add a 4-Way connector to the rear of the vehicle.
  view full answer...


• Recommended Trailer Hitch For 2014 Chevrolet Impala LTZ
  
• The Curt Trailer Hitch, part # C12115 is confirmed as a fit for your Impala. This is a Class ll hitch and it has a 1-1/4 inch receiver opening. Per Curt, all non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps like part # 18050. Failure to properly support these loads will void your hitch warranty from Curt. For that reason I recommend going with the Draw-Tite Trailer Hitch, part # 36538. This is also a Class ll hitch and it does...
  view full answer...


• What Hitch Fits a 2016 Mazda 3 Hatch i-Touring
  
• When it comes to "Vehicle Style" in our fit guide, there are 4 options in the drop down menu for a 2016 Mazda 3 - "Hatchback - with LED Taillights", "Hatchback - without LED Taillights", "Sedan - with LED Taillights", and ""Sedan - without LED Taillights". Since you mentioned your Mazda was a Hatch i-Touring, that narrows things down to the pair of hatchback options. Choosing either one of those options from the drop down menu will bring you to the two available hitches, the Draw-Tite...
  view full answer...


• Recommended Tow Package for 2018 Mazda 3 Sedan
  
• To set your 2018 Mazda 3 up for towing a light trailer you will need a trailer hitch, wiring harness, ball mount, and hitch ball. Starting with the hitch I recommend the Draw-Tite Sportframe Trailer Hitch Receiver # 24912 because it offers the easiest install process that doesn't require any modification to the underbody trim panel on your vehicle like with the other available option. It is a Class I hitch that features a 2,000 pound towing weight capacity and will provide you with...
  view full answer...


• Does Draw-Tite Class 1 Receiver Hitch Need A Stabilization Strap?
  
• No. The Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # 24956 for your 2017 Chevrolet Bolt EV does not require a stabilization strap for any non-towing accessory like the Curt hitches. If you will be using this hitch for towing, I recommend the Sportframe Drawbar 2-1/8" Rise or 2-3/4" Drop 2000 lb Kit # 3593 along with hitch ball # 19258 for 2 inch or # 19256 for 1-7/8 inch hitch ball. For your vehicle wiring, I recommend the Tekonsha Upgraded Modulite...
  view full answer...


• Recommended Trailer Hitch For 2018 Chevy Cruze
  
• Trailer hitches are given a class rating based on their maximum weight capacity and receiver opening size. The classes range from Class I which has the lowest capacity (2000lbs and under) and a 1-1/4" x 1-1/4" opening to Class V which has the highest capacity (around 20,000lbs) and, typically, a 2-1/2" x 2-1/2" opening.. The towing capacity of a Cruze is only near 1000 lbs (check owners manual). Due to the towing capacity of the Cruze we are only able to offer trailer hitches with 1-1/4"...
  view full answer...


• Recommended Trailer Hitch for 2014 Toyota Prius C
  
• To a tow a trailer with your 2014 Toyota Prius C you're going to need a trailer htich. I recommend the Draw-Tite Sportframe Class I Trailer Hitch Receiver # 24971. This hitch has a 2,000 pound maximum towing weight can requires no drilling to install. To power your trailer's lights you'll need a wiring harness. The Tekonsha T-One Wiring Harness # 118680 will give you a 4-way connector on the rear of the Prius. There's no need to cut any wires, this harness plugs right into your car's...
  view full answer...


• Trailer Hitch Recommendation for 2018 Honda Accord
  
• For your 2018 Honda Accord the Draw Tite part # 24972 is the winner. One reason is that the price is way better, but mainly because you said you were going to carry a bike rack. Unlike the Curt hitch for your vehicle # C11525 this hitch does not require the use of a stabilizer strap when carrying a non-supported load like the Curt does. For trailer wiring you'd then want the part # 119250KIT which is a confirmed fit, then for a ball mount part # 3593 and hitch balls # 19258 for a 2 inch...
  view full answer...


• Trailer Hitch Recommendation for 2014 Chevy Cruze Diesel
  
• For a trailer hitch that is confirmed as a fit for your 2014 Chevy Cruze diesel we have the Draw Tite part # 24882. I prefer the Draw Tite hitches over the Curt hitches as they do not require a stabilizer strap when carrying a non-supported load like a bike rack. For wiring I recommend the Tekonsha kit part # 118508 as we have found that the Tekonsha brand harnesses are more reliable than the others. For a ball mount you would want the # 3593 and then for a 2 inch hitch ball part...
  view full answer...


• Recommended Trailer Hitch Receiver, Wiring, and Ball Mount For 2017 VW Golf SportWagen
  
• For your 2017 Volkswagen Golf SportWagen, I recommend the Curt Trailer Hitch Receiver Class I - 1-1/4", # C11422. This is a confirmed fit for your vehicle and works great for light duty towing like you are referring to. You will also need a ball mount to go with your hitch receiver, and I recommend the Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs, # C45521. This ball mount will require a 1-7/8 inch hitch ball like # 19256 or a 2 inch ball like # 19258. For...
  view full answer...


• Trailer Hitch and Wiring for a 2017 Volkswagen Golf Alltrack
  
• Trailer hitch # 24949 is a fit for the 2017 Volkswagen Golf Alltrack. It also is listed for all models of the 2017 Golf Sportwagen. I have included a link to the installation instructions for you. If you plan on doing some towing the recommended ball mount is # 3590. For a 1-7/8 inch ball use # 19257 and for a 2 inch ball use # 19258. And for trailer wiring you can use # 118730 to add a 4-Way flat to the rear of the vehicle. If you want to use the hitch for an accessory such as a...
  view full answer...


• Trailer Hitch and Wiring Harness Recommendation for 2019 Chevy Malibu
  
• The trailer hitch I recommend for your 2019 Chevy Malibu is the Draw-Tite Trailer Hitch # 36652 because it has a concealed crosstube and is a bolt-on installation that will not require drilling into your vehicle's frame to install. This Class II, 1-1/4" trailer hitch is almost entirely hidden behind your bumper, as you can see by the accompanying photo of this hitch installed on a Malibu. The hitch has a black powder coat finish to protect it from corrosion, has a 3,500 lb towing capacity...
  view full answer...


• Is The Rear Bumper On A 2002 Toyota Tundra Towable
  
• Yes, as long as you have 3 holes in the rear bumper on your 2002 Toyota Tundra (2 for safety chains and 1 for the hitch ball) they can be used for towing. You will also want to use a hitch ball like part # 19256 for 1-7/8", part # 19258 for 2", and part # 63840 for 2-5/16". According to your owner's manual, the bumper on your truck is rated up to 500 lbs. tongue weight (TW) and 5,000 lbs. gross trailer weight (GTW). As long as you are within this range, you can safely use the bumper to...
  view full answer...


• How Much Weight Can be Carried with a Cargo Carrier on a 2015 Ford Mustang
  
• Let me start by saying you're definitely asking all the right questions to make sure you can safely carry your gear on a cargo carrier and you're definitely right to question what you were told. Most of what you're asking are things that we often tell people and they're completely taken off guard and surprised. 1. Yes, tongue weight matters and it is the only capacity requirement you need to worry about. Tongue weight is the force pushing down on a hitch from the weight that's suspended...
  view full answer...


• Recommended Trailer Hitch Receiver For 2006 VW Beetle TDI
  
• The Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # 24679 is a confirmed fit for your 2006 VW New Beetle TDI. I recommend the Draw-Tite Drawbar for 1-1/4" Hitch # 3593 along with the 2" Hitch Ball # 19258 to match your trailer coupler. I recommend the Upgraded Circuit Protected Tail Light Converter Hardwire Kit with 4-Pole Connector (Includes Tester) # 119178KIT for your TDI trailer wiring. This will give you a 4-way flat trailer connection.
  view full answer...


• Trailer Hitch and Wiring for a 2017 Ford Fusion Sport
  
• For the Sport model of the 2017 Ford Fusion you will actually need hitch # C12164. The recommended ball mount for this hitch is # C45016. For a 1-7/8 inch ball use # 19257 and for a 2 inch ball use # 19258. And for trailer wiring you can use # 118574 to add a 4-Way flat connector to the rear of the vehicle. I have linked a video showing an example installation of the wiring for you.
  view full answer...


• Recommended Trailer Hitch for 2015 Dodge Charger Hellcat
  
• I called my contact at Curt and asked about the Trailer Hitch Receiver, part # C12064. They said they could not guarantee it would fit your Hellcat. It is a Class ll hitch and has a 1-1/4 inch receiver opening. I also called Draw-Tite and asked about the fit of the # 36548 Class ll hitch. They said this hitch will work with your Charger Hellcat. This hitch has a 1-1/4 inch opening. If you are going to tow with the hitch I recommend part # 36061 for a drawbar. This has a 3-1/8 inch...
  view full answer...


• Hitch Recommendation for 2019 Chevy Trax
  
• The 2019 Chevy Trax is rated for towing and we do have the Draw Tite hitch part # 36554 that fits this vehicle that has a 3,500 lb towing capacity which would be more than enough for a log splitter. Your vehicle looks to have a towing capacity of between 1,500 and 3,500 lbs depending on how it's equipped as well. Then for trailer wiring you'd want the part # 118659 for if you have an LS model or the part # 118751 for if you have an LT or a Premier. Then for a ball mount you'd want...
  view full answer...


• Least Visible Trailer Hitch Recommendation for 2015 Ford Mustang Fastback
  
• The Draw Tite hitch part # 24928 would be less visible than the Curt # C11405 because it sits 1/2 an inch higher and it doesn't have a collar around the opening of the hitch. Instead it's just an open shank which would be slightly less visible. For trailer wiring you'd then want the part # 118487 which is a confirmed fit. For a ball mount you'd then want the part # 3594, 2 inch hitch ball # 19258 or 1-7/8 inch ball # 19256.
  view full answer...


• Ball Mount Recommendation for a 2017 Chrysler Pacifica with Draw-Tite Trailer Hitch 36798
  
• Your assumption is correct. If the distance from the ground to the top of the receiver opening on trailer hitch # 36798 is 12 inches, and the distance from the ground to the bottom of a level trailer coupler is 17 inches, you would need a ball mount with a 5 inch rise. Ball mount # 36065 is a good option. It takes a ball with a 3/4 inch diameter shank. For a compatible 1-7/8 inch ball you can use # 19256. For a 2 inch ball use # 19258. For trailer wiring if your 2017 Chrysler Pacifica...
  view full answer...


• Recommended Trailer Hitch Receiver for 2009 Subaru Impreza WRX Sedan with Dual Exhaust
  
• For your 2009 Subaru Impreza WRX sedan with dual exhaust, I recommend the Draw-Tite Sportframe Trailer Hitch Receiver # 24807 over the Curt # C11317 because Curt requires use of a security strap for cargo carriers and bike racks that Draw-Tite does not. If you will be doing light towing with this hitch receiver, I recommend the ball mount # 3594 and hitch ball # 19256 or # 19258 for a 2 inch diameter ball. For wiring, I recommend the T-One # 118464 which is an easy installation...
  view full answer...


• Trailer Hitch That Fits a 2018 Honda Civic Sedan
  
• There is a trailer hitch that will fit a 2018 Honda Civic sedan but the Curt Trailer Hitch Receiver # C11463 will only fit a '18 Honda Civic hatchback (excluding those with a center exhaust). Instead you will want to use the the Draw-Tite Sportframe # 24954, which will fit a 2018 Civic sedan (excluding those with a center exhaust); the correct drawbar for this hitch is the Draw-Tite # 3593 which does come with a pin and clip; you will need 1-7/8" Hitch Ball # 19256 or 2" Hitch Ball #...
  view full answer...


• Curt or Draw Tite Hitch Recommendation for 2013 Chevy Cruze
  
• The mounting brackets of the Curt Hitch part # C11282 are much bigger than the Draw Tite hitch part # 24882. That is the weight difference. If it were me I would go with the Draw Tite. It has a better price, the same capacities, doesn't require a stabilizer strap like the Curt does with non-supported loads, but also because the lighter weight will make it easier to install. For trailer wiring you would want the part # C56214, for a ball mount part # 3593, and then for hitch balls...
  view full answer...


• Recommended Trailer Hitch Receiver for 2018 Nissan Rogue Compatible with Tailgate Lift Assist
  
• For your 2018 Nissan Rogue SL, I recommend the Draw-Tite Trailer Hitch Receiver # 36542. This is a class II hitch receiver rated for up to 300 lbs tongue weight and well over the towing capacity of your vehicle at 3500 lbs. The ECU is not something we carry as most liftgates work just fine when you add an aftermarket hitch. The sensor that is often covered up at the hitch location just won't sense the movement, but either side of the hitch tube will work fine. If you have issues, then...
  view full answer...


• Trailer Hitch and Wiring for a 2017 Chrysler Pacifica
  
• The Curt Class II hitch that fits the 2017 Chrysler Pacifica is # C12180. But if you want to use this hitch for an accessory such as a bike rack or cargo carrier Curt requires the use of stabilization strap # 18050 per their warranty requirements. To avoid having to use the strap I recommend using Draw-Tite hitch # 36798 which does not have the strap requirement. If you plan on doing some towing the recommended ball mount is # 36071. For a 1-7/8 inch ball use # 19256 and for a 2 inch...
  view full answer...


• Best Trailer Hitch Receiver for a 1999 Buick LeSabre
  
• We currently only have one trailer hitch receiver for your 1999 Buick LeSabre which is the Draw-Tite Trailer Hitch Receiver part # 36216. This option will give you a Class II hitch with a 1-1/4" receiver tube opening. I have attached an installation video on a similar 1997 Buick LeSabre for you as well. If you can tell me what you will be using the hitch for I would be glad to offer some additional recommendations for you as well.
  view full answer...

Do you have a question about this Hitch Ball?