Curt Double Lock, Flip and Store Underbed Gooseneck Hitch w/ Installation Kit - 30,000 lbs

I installed the Curt gooseneck on my 1993 GMC 2 Wheel Dr. 2500 truck. All the components have tight tolerances. It took me eight hours. With a socket and the wrench. Laying on my back. I did have to cut the wheel well lip about 3/8 of an inch off because I could not get that front angle bar to slide in without hitting it, no way around it unless you lift the bed up and I wasn’t going to do that!!. You have to cut it.instructions do not state that. I’m very happy with the Hitch, it is definitely stout! I did have to make a notch on the outside brackets to go over my airbag bolt. I also had to remove the support bracket on the inside of the frame for the airbag and the crossmember for the spare tire to get the front angled bar in.1293750

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

by: Jonathan 08/22/2023

1995 Chevrolet C/K Series Pickup

Used this kit to modify and fit my c notched lowered truck. Side plates welded to notch and hitch assembly is still removable. Kit was as described and am pulling 19k wit it and zero problems1652215

by: Raymond 12/08/2021

This is an excellent product. I installed the hitch myself and it was pretty straightforward. I did a lot of research on installing a below bed hitch to make sure it went well. I did have a small issue with getting one of the bars in. I put a call in and got great customer service. After a year of use I have had no issues at all. I will definitely use etrailer in the future.1220114

Raymond

12/9/2022

It has been two years of use with this hitch and it still works perfectly. I have had no issues at all.

Direct bolt up for 1997 Chevrolet C 2500 took me approximately an hour and a half to install and never removed the bed1092900

Thomas

7/14/2022

Great

by: Will J10/09/2019

1996 Chevrolet C/K Series Pickup

I purchased this gooseneck hitch about a year ago to go on my pickup. I didn't install it right away as I didn't have a trailer that needed a gooseneck hitch. I installed the hitch in April of 19 when I found a trailer that I wanted and needed to transport it. Everything installed smoothly and in about 4 hours. I was taking my time and triple measuring to make sure I didn't cut or drill holes in the wrong location. All of the bolt holes line up on the frame and the only drilling that I had to do wad through the floor of the bed for the hitch to come through and the u-bolts for the safety chains. Make sure that you read the instructions completely and carefully and the installation is a breeze. I am happy with this hitch and would buy another one for any new truck that I get.715171

Perfect fit, sturdy, and instructions were almost perfect. Install time approx. 5 hr. without lift. Loosen and lift truck bed would have saved about 1 hr. Overall simple to install, all bolting points and hole were perfect .
Excellent Customer Service.
Special thanks to all who helped on ordering and shipping.425338

Hal

8/26/2018

Used this 4 or 5 times and works great. Checked all bolting points and still tight and secure. So far so good, working great.

Very fast shipping I’ve not got to install yet1180735

Charles

10/16/2022

The curt turnover ball works great

Will be returning. Crossbar pieces didn’t line up with bolt holes on brackets bolted to the frame. Angle iron crossbar didn’t even fit inberween the bed and frame. Also the bolts to go in the rear cross bar didn’t even thread in either the threads on the cross bar were the wrong size or the bots were the wrong size. 619508

Works great and easy to install 1437508

by: Clint M03/09/2020

After a year of owning still looks great and performs great, install instructions were spot on and haven’t had any issues with hitch,use it almost every weekend. 764558

by: Dave M01/07/2020

Chevrolet

Installed in a ‘95 Chevy K3500. Fit perfectly, easy install. Works like it should -no issues. Can highly recommend.736228

by: Kylee10/17/2020

Hauls my trailer AMAZING!!!!! 900372

by: Ryan 04/17/2021

Great fit was very easy to install 1014121

by: Nathan 12/24/2021

1230678

by: K.L.06/28/2023

Great product but the instructions are a little muddied. I replaced a welded in under bed gooseneck hitch with this unit. I chose this unit over a single pin gooseneck flip ball for the added mental security as well as potential for less rattle1610572

Click to Enlarge

by: Ron04/08/2023

2014 F150
Wow, what can I say, this is an extremely solid, well built unit.
I knew it was about 90 pound, but when you take it out of the boxes the quality really hits you. Everything fits just as it is supposed to. The bolts are all Grade 8, and when you get everything torqued you know this unit is truly part of the truck frame.
Maybe a little over kill for our 5500# Escape 5.0 TA, but I wanted that confidence while connected, and I got it.
Coupled this with the Anderson Ultimate Hitch in Black Out and couldn't be happier.1552669

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

by: Nick10/30/2021

this installed correctly on my 2005 dodge ram 2500 diesel per instructions for installation with air bags. I have hauled a 42 foot 3 axle car trailer for over 6,000 miles with no issues. This was a great purchase. Thank you1191271

Click to Enlarge

by: Patrick 11/18/2023

It's worked flawlessly for over 15k miles pulling an 8500lb 5th wheel trailer with my F150. I had U-Haul install it because it is basically a two-man job, but I'd do it myself if I had to do it again. REMINDER, be very precise when measuring and cutting the hole on the truck bed.1694313

Product is very good I’ve installed several of these hitches but this time the packaging was terrible. The crossmember bars were hanging out of the box the bolt packages were opened and I was missing bolt hardware to install the hitch. The wires used to pull the bolts through the frame one of them looked like it had been used and was all deformed to the point I couldn’t use it. Not sure if this was a restock hitch or what put all the packaging was terrible and missing parts.1585693

by: Dan11/13/2020

Installed easily on 2015 GMC 2500 HD double cab short bed. Plenty of clearance under the bed when ball is flipped. This system makes for a clean useable bed. When I was purchasing this I was concerned about clearance of a gooseneck hitch and my transfer tank. I have a 40 gal tank that sits back from the cab a bit over 20 inches, there’s plenty of clearance for a gooseneck with a fuel tank on this short bed. The hitch has held up perfectly over the last year. I haul around 12k on steep, washboard, gravel roads.911666

Click to Enlarge

Click to Enlarge

by: roger04/20/2021

Thank you for reaching out. Definitely love the reliability and durability of this hitch, also the added clearance. I have it mounted on my 40 foot enclosed race car trailer. We towed using it 35 to 40 times to and from race tracks in 2019. Hooking it up and disconnecting it every weekend. Never gave us a single issue.1016782

Click to Enlarge

Click to Enlarge

Fist I should say that this does seem beefy and I expect it will work fine for towing my 5th wheel. This was the most difficult installation I've ever experienced due to poor design, & poor workmanship. They clearly saved every penny they could by using low quality machining. This thing took me 3 days of cussing Curt. This is my 2nd Curt product and the first was similar, but not as bad as this. I willnever buy another Curt product.1636079

I think this gooseneck hitch is the best for newer Sierra/Silverado HD trucks. I installed it a week ago with the help of my father-in-law and his car lift. Took about 4 hours moving slowly and taking our time. Everything fit well and bolted right up. I also reinstalled the foil heat shield after removing one mounting ear. I did not drop the exhaust or the plastic heat shield and still got everything in.

I chose this specific kit because it did not require notching the bed seam when installing the rails. It also has a higher tongue load rating than the others and was cheaper.

The only major criticism I have is the pull wire and carriage bolts. My chassis has weld nuts and I would have preferred to use those over carriage bolts pulled into the chassis. I am thankful there were access holes almost inline with the mounting holes. That made it easy to put pressure on the bolt heads so they didn’t fall back. I also think the gasket around the big hole should be one piece to make it look cleaner. I used black silicone rtv to smooth the transition and adhere the gasket in place.

Overall I am completely satisfied with the kit and the help of Shawn B who got my order in, had it shipped that same day and followed up with me after delivery. Thanks etrailer and Shawn B. 468718

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

by: Irakli09/08/2023

It was working great. I had 2 car carrier trailer Hitch on it , with 25k lb all the time. Works perfect.
I like it.1663252

Ordered this after deciding to go with it over a B&W kit due to me not using it a whole lot and the price difference. When I received the package 1/2 the hardware was missing because the inner box it was in was all broke apart and the outer box was not sealed up. So I would have to give the packaging and shipping one star because I had to go spend an extra $75 on grade 8 hardware. The paper directions were not totally clear on several thing so we resorted to the video which helped a lot. The two large carriage bolts that go in the rear cross member are a little deceiving because the video makes it seem like they slip right in. However, the heads were larger than the pass through in the frame rails so it took quite a bit of extra time and ingenuity to get those fished through there with the plates.(The carriage bolts survived shipping so they were what came with the kit). In the video it showed where he cut a large u out of the inner fender to clear the pull handle and notched the bed that looked kind of sloppy. With a few extra measurements you can just cut a hole in both for handle to slide through and give it a much cleaner look. Definitely recommend putting a bolt through receiver holes and using a strap to hold up center plate through hole in bed after you get it into place. Makes life a lot easier until you get the bolt ls in. Overall this hitch works and functions great. Install went pretty smooth with two people and I would recommend it to anyone needing a hitch.1343119

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge