Derale High-Temperature Replacement Hose for Transmission Applications - 5' Long

Ask the Experts about this Derale Accessories and Parts

• Recommended 2011 Honda Odyssey Transmission Cooler And Thermostat
  For your 2011 Honda Odyssey, the transmission cooler I recommend is the Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets - Class III - Efficient # D13503. This is a plate-fin cooler with furnace-brazed aluminum construction and 3/4 inch wide turbulator plates for more efficient cooling. I recommend Derale thermostat # D13011 with mounting bracket # D25793, and extra hose # D13016 for this installation. The thermostat will allow 90 percent of the fluid to bypass the...
  view full answer...
• Can Stacked Plate Transmission Cooler Install in 2009 Chevy Avalanche
  Yes, the Derale transmission cooler part # D52506 does fit your 2009 Chevy Avalanche but to install it you are going to want the snap in adapter part # D13035 and the rubber line part # D13016 with the Derale -6 AN Female Barb Fitting # D98200 to complete the install.
  view full answer...
• Stacked-Plate Transmission Cooler for 2018 GMC Acadia SLT with V6
  Transmission and oil coolers are not vehicle-specific; you can essentially install any one for which you have the space available to install it. When it comes to coolers bigger is better. And if you want the best cooling even at lower speeds, such as when driving in mountainous areas, you might consider a remote-mount fan-powered cooler like the Derale Atomic Cool # D13950, an efficient plate-fin type cooler that will lower your transmission temperature even at low speeds since it does...
  view full answer...
• When Installing a Transmission Cooler Can the Inlet/Outlet Ports Face Down
  Yes, you can install a transmission cooler like the Derale 25-Row Stacked-Plate Cooler part # D52506 so that the inlet and outlet ports are facing down. The inlet and outlet ports do not need to be pointed in any one specific direction as the line pressure will work to pump the fluid though the inlet of the cooler and out the outlet to be returned back to the transmission. In order to install the above you will need the following: Derale -6 AN Female Swivel part # D98200 Derale High-Temperature...
  view full answer...
• Installing Hoses on Flex-a-lite Transmission Cooler
  The Flex-a-lite Transmission Cooler - Plate and Fin - 17 Row - Barbed Fitting # FLX400117 has the 3/8 inch barbs. Since the hose doesn't fit as tight as you'd like, I recommend using the Derale High-Temperature Replacement Hose for Transmission Applications - 5' Long # D13016 which does have the 3/8 inch inner diameter. When installing the transmission cooler hoses, I recommend leaving the hose out in the sun for a little while to allow it to heat up a little and become more pliable....
  view full answer...
• Parts Needed to Install Transmission Cooler # D13311 in a 2011 Jeep Liberty
  You would need the AN fitting adapters part # D98200 for each end of the cooler and then the clamps part # D13008 for securing the hose to the line, and for hose part # D13016. Most likely you will also need the insta-dapt fitting part # D13004 as well.
  view full answer...
• Will the Derale 25-Row Stacked-Plate Cooler Fit a 2005 Chevy Silverado 2500
  The stacked-plate transmission coolers like the Derale 25-Row, High-Performance, Stacked-Plate Cooler with -6 AN Fittings part # D52506 do offer superior cooling power when compared to plate-fin and tube-fin designs. However, they are also much thicker at 2" which means you will need to make sure you have this much depth in addition to the length and height of 13" wide x 9-3/16" tall. There should be plenty of space behind your grille for this cooler so I don't think you will have any issues....
  view full answer...
• Best Transmission Cooler Recommendation for 2013 Chevy Silverado with 6.2 liter V8
  Stacked plate transmission coolers are by far the most efficient ones available. The largest one we have is the part # D54006 which measures 13" Wide x 13-11/16" tall x 2" deep. For a bracket kit you would need the part # D50020, for AN fitting adapters you'd need two of the # D98200. For the fitting for your truck you would want the part # D13035. For a 5 foot section of hose we have the part # D13016.
  view full answer...
• Derale Class V Transmission Cooler for 2011 Silverado 5.3L
  The Derale high-efficiency Class V stacked plate transmission cooler # D52506 can replace your current cooler as long as you have the space for mounting it (it measures 13W x 9-3/16 x 2). This cooler will work well as a replacement for the KNP and will provide better cooling. You can install it with the 6AN fittings facing in any direction. The kit includes just the core and the aluminum 6AN fittings. If you need to connect to hose barb oil lines you can use 6 AN Female Swivel Fitting...
  view full answer...
• Engine Oil Cooler Recommendation for a 2001 Jaguar XKR with Leaking Factory Cooler
  The Derale 10-Row, High-Performance, Stacked-Plate Cooler # D51010 could work for you, but since we do not have a fitting like the ones on your current oil cooler you will need to cut the metal lines and use the rubber line part # D13016 with the Derale -10 AN Female Barb Fitting # D98203. The mounting bracket dimensions this cooler was designed to fit is 12-1/4 inches wide. Hopefully your bracket is the same and it will bolt right up.
  view full answer...
• Will a Remote Transmission Cooler Fit a 2005 Ford F-250 with 5.4 Liter
  The great thing about the Derale remote transmission cooler # D13950 is that you can mount it where ever you have space. Since it has its own fan it does not have to be placed out in front of the motor. This will allow you to position it in the place with the most room and that does include areas outside of the engine compartment! The only stipulation you will want to follow is not to place it too low or to where the fan or fins are facing the ground because something could bounce up...
  view full answer...