Derale Stainless Steel Hose Clamps (4 Piece)

Ask the Experts about this Derale Accessories and Parts

• Will the Derale 25-Row Stacked-Plate Cooler Fit a 2005 Chevy Silverado 2500
  The stacked-plate transmission coolers like the Derale 25-Row, High-Performance, Stacked-Plate Cooler with -6 AN Fittings part # D52506 do offer superior cooling power when compared to plate-fin and tube-fin designs. However, they are also much thicker at 2" which means you will need to make sure you have this much depth in addition to the length and height of 13" wide x 9-3/16" tall. There should be plenty of space behind your grille for this cooler so I don't think you will have any issues....
  view full answer...
• Transmission and Power Steering Cooler Recommendation for a 2005 Honda Odyssey
  Since you are planning on buying a transmission cooler like the Derale Transmission Cooler, part # D13502, I would consider purchasing the Derale Combination Cooler Core, part # D15321. This cooler can be used for cooling both the transmission fluid and the power steering fluid on your vehicle in one compact package, see photo at right. You will need to measure to decide if you will be able to mount the transmission cooler first. The dimensions of the Derale Combination Cooler Core are...
  view full answer...
• Can Two 40 Row Derale Transmission Coolers be Used in Place of a Factory Cooler
  Yes! You can use 2 of the Derale 40-row coolers # D54008 to cool the transmission fluid on your prostreet car. The stacked plate design is the most efficient at cooling. To optimize cooling make sure the coolers are mounted where they can get the most air flow (right behind the grille). I also recommend a couple of mount kit # D50020 and some hose. For a 25 foot length with an inner diameter of 11/32" use # D13007. For 25 feet of a 3/8" diameter use # D13017. We also have a 4-pack of...
  view full answer...
• Parts Needed to Install Transmission Cooler # D13311 in a 2011 Jeep Liberty
  You would need the AN fitting adapters part # D98200 for each end of the cooler and then the clamps part # D13008 for securing the hose to the line, and for hose part # D13016. Most likely you will also need the insta-dapt fitting part # D13004 as well.
  view full answer...
• Can a Remote Transmission Cooler Be Mounted Under the Front of a Truck Bed
  Technically, with enough extra hose, you could mount it anywhere that is safe and does not expose the cooler core to road debris. I have not heard of anyone mounting a cooler in your chosen location though. You would also most likely need more transmission fluid because of the extra hose that would be needed. I recommend staying under the hood because the less hose that is used the less likely it is to get damaged. Plus it will be easier to install. If extra hose is needed a ten foot...
  view full answer...
• Recommended Transmission Cooler for a 2013 Chevy Tahoe
  I have the perfect transmission cooler option for you. Generally speaking, the best transmission cooler to use would be the largest one you have available space for. The best place to install a transmission cooler is in front of the radiator/condenser behind the grill on your 2013 Chevy Tahoe. I recommend using the Derale 25-Row, High-Performance, Stacked-Plate Cooler part # D52508 because the plate and fin technology incorporated into this transmission cooler is far more efficient than...
  view full answer...
• Transmission Cooler Recommendation for a 2015 Toyota 4Runner
  Transmission coolers don't have specific fits, but if you have room for the # D52506 in front of your radiator/AC condenser then it would work well. It measures 13" Wide x 9-3/16" tall x 2" deep. This is one of the most efficient coolers on the market that would work great on your vehicle. To install this cooler you will need a few other components. Part # D50020 for a bracket kit, part # D98200 for a fittings (you'll need two of these), hose clamps part # D13008, and rubber hose part...
  view full answer...
• Transmission Cooler Recommendation for 2012 Ram 3500, 6.7 Cummins with 6 spd Automatic
  The best way to install a supplemental transmission cooler in line with a factory transmission cooler is to put the supplemental cooler after the factory cooler. To do that you will need to determine which of the lines from the factory cooler is the outlet. To do that you will want to start your truck when its cold, put it in drive for about 10 seconds with the brake on, put it back in park and shut the truck off. Next you will want to grab both transmission lines feeding into the cooler....
  view full answer...
• Transmission Cooler Recommendation for 2007 Dodge Ram with Cummins Diesel
  For a full size diesel truck you'd need all the cooling power you can get if you plan to bypass your factory cooler. Stacked plate coolers are the most efficient styles of coolers around so the part # D54010 would be your best option. To complete the installation you will want two of the barb hose fittings, part # D98202, replacement rubber hose # D15799, hose clamps # D13008 and insta-dapt radiator adapter # D13004. The mounting kit is # D50020.
  view full answer...
• Fluid Leaks After Installing the Derale Adjustable Fan-Control Thermostat # D16769
  It is surprising to hear your hose is leaking after installing the Derale Adjustable Fan-Control Thermostat, # D16769. We have not received any complaints for this product. I spoke with my contact at Derale and he said there are only a few things that typically cause leaking with this thermostat. First, make sure the included foam pad is placed over the capillary tube. Next, look at the type of hose clamp you are using. If you are using a clip, I recommend replacing it with a screw...
  view full answer...
• Most Efficient Transmission Cooler Recommendation for 2015 Chevy Silverado 1500
  The most efficient style of transmission cooler is the stacked plate style like the part # D54012 that you referenced. So for the largest one in this style you'd want the # D54010 which measures 13W x 13-7/8T x 2D Inch and you'd have an extremely efficient cooler. To complete the installation you will want two of the barb hose fittings, part # D98202, replacement rubber hose # D15799, hose clamps # D13008 and insta-dapt radiator adapter # D13004. The mounting kit is # D50020.
  view full answer...
• How To Reduce Both Engine Oil and Transmission Fluid Temps On A 2005 GMC Sierra 2500 While Towing
  I have attached a list of parts that I recommend for your 2005 GMC Sierra 2500 to help with cooling both the engine oil and transmission fluid while towing. Derale Hyper-Cool Remote Transmission Cooler Kit part # D15960 Derale Hyper-Cool Remote Engine Cooler Kit part # D15660 Derale Snap-In Radiator Adapter Fitting part # D13035 Derale High-Temperature Replacement Hose part # D15799 Derale Stainless Steel Hose Clamps part # D13008 1/2" Barb to 1/2" Barb Union Fitting part (Local...
  view full answer...
• Transmission Cooler for a 2013 GMC Yukon XL
  The transmission coolers that we carry are meant as supplemental coolers to the factory cooler though some people do decide to bypass the factory cooler for any number of reasons. The term tow package means different things to different manufacturers but it does often include a supplemental cooler. Adding a cooler is an inexpensive way to help get the most life out of your transmission, especially when towing. Transmission coolers are not vehicle specific. However, if you happen to...
  view full answer...
• When Installing a Transmission Cooler Can the Inlet/Outlet Ports Face Down
  Yes, you can install a transmission cooler like the Derale 25-Row Stacked-Plate Cooler part # D52506 so that the inlet and outlet ports are facing down. The inlet and outlet ports do not need to be pointed in any one specific direction as the line pressure will work to pump the fluid though the inlet of the cooler and out the outlet to be returned back to the transmission. In order to install the above you will need the following: Derale -6 AN Female Swivel part # D98200 Derale High-Temperature...
  view full answer...
• Recommended Transmission Cooler for 2001 Toyota Tacoma
  For your 2001 Tacoma I recommend the Derale Series 8000 Plate-Fin Transmission Cooler Kit, part # D13502. This is a Class lll cooler that measures 11-inches wide, 7-1/4 inches tall, and 7/8-inches deep. This cooler is recommended for mid-size cars, SUVs, and trucks like your Tacoma. I have attached a drawing that shows how the hoses need to be run when installing the cooler. If you find your hose is not long enough to attach to the new cooler, you may need an additional Derale Insta-Dapt...
  view full answer...
• Supplemental Transmission Cooler Recommendation for a 2008 Cadillac Escalade
  Actually for best results you would want to keep your factory transmission cooler and then add a supplemental one like the part # D52508 that you referenced. You would also need two of the barb fittings part # D98202 and then hose like part # D15700 and hose clamps # D13008 as well. You will want to route the cooler downstream of the factory cooler so that it first goes through it and then through the Derale. Your fluid temps are crazy high right now, but with an efficient cooler...
  view full answer...
• What Pressure are the Derale Transmission Coolers, Fittings and Hoses Rated For
  All of the Derale transmission coolers, fittings and hoses that we carry are tested for use up to 300 psi. Along with this cooler you might need the following parts for installation as an engine oil cooler: 10 AN Hose Fittings, # D98203 Remote Engine Oil Cooler Installation Kit, # D15752 Stacked-Plate Cooler Bracket Kit, # D50020 If installing this cooler as a transmission cooler you might need the following parts: 10 AN Hose Fittings, # D98203 Stacked-Plate Cooler Bracket Kit,...
  view full answer...
• Power Steering Cooler Recommendation for an Off-road Rock Crawler
  Typically, in automotive applications, the addition of a supplemental cooler will drop the fluid temperature around 10 to 20 degrees Fahrenheit. Keep in mind, this is with the cooler mounted directly behind a vehicle grille, receiving good airflow. For your situation, I would recommend a different product. The power steering cooler, # D13310, that you referenced will help, but the lack of airflow will probably not give you the results you are looking for. Instead, I recommend looking...
  view full answer...
• What is the Length of the Hose in the Derale 8000 Series Transmission Coolers
  The hose that comes with the # D13502 and # D13503 transmission coolers is 4 ft long. This is the same with all Derale 8000 Series transmission coolers. If you need additional hose length, we offer a 4 ft long individual hose, # D13003, and a 25 ft hose, # D13007. You may also need additional hose clamps, # D13008, if you purchase additional hoses.
  view full answer...
• Additional Hose Needed for Installing the Derale Series 8000 Kit # D13502 on a 2016 Nissan Frontier
  Depending on where you install the Derale Series 8000 Plate-Fin Transmission Cooler Kit # D13502 on your 2016 Nissan Frontier, you may or may not need some additional hose. As you saw from the installation video on a 2014 Frontier (which is linked), some additional hose was required for the install. You can aquire new hose from our site using part # D13003 should you need it. This hose is 4 feet long and should be enough for your application. You may also need some additional clamps...
  view full answer...
• Recommended Transmission Cooler and Parts Needed for Installation on 2011 GMC Sierra
  For your 2011 GMC Sierra I recommend using a Derale 10,000 Series Stacked-Plate Cooler with -10 AN Fittings, like # D52510. I spoke with my contact at Derale and he said these coolers are popular among Allison transmission owners. When choosing a transmission cooler, the largest cooler that will fit in the space available in your engine compartment is typically the best. Generally speaking, the larger the cooler the better the cooler performance. A stacked-plate cooler is the most efficient...
  view full answer...
• Remote Transmission Cooler and Mounting Accessories for a 2004 Chevy Suburban 5.3 Liter
  Using the GM-specific snap-in radiator adapter fitting # D13035 will make installing a transmission cooler such as # D12733 easier because with it you would not have to cut and flare any lines for installation. The core on this cooler has 6 AN fittings. This cooler does not come with a thermostat but one can be added using # D13021. You will also need a mounting kit such as # D13002, hose clamps such as # D13008, and hose # D13017. The other option is a remote cooler that comes with...
  view full answer...
• Can Extra Ports on Filter Landing of Derale D15749 Relocation Kit Be Used to Install an Oil Cooler
  You certainly can. To install a cooler, you'd just need a cooler such as # D15452, two fittings, part # D98103, some replacement hose like # D15701 and some pipe clamps like # D13008. Remove the plugs, install the fittings, place the cooler where it'll catch air and run the hose. You'll want to use teflon tape like # A05-0265 on the fittings installed into the filter landing.
  view full answer...
• Best 2 Inch Trailer Hitch for a 2004 Honda Pilot with Full Size Spare Tire
  All of the Class III hitches that we have available for the 2004 Honda Pilot install in much the same way and have the same towing capacity. None of the hitches require permanent removal of the spare tire, full size or space saver. This leaves the look of the hitch and cost as the only real difference between the available options. The Draw-Tite model you selected, # 75599, is a good choice. Some Items you may want to consider if towing with your Pilot are a transmission cooler and power...
  view full answer...
• Fittings and Other Parts Needed to Install Transmission Cooler D52508 in a 2010 Chevy Tahoe
  Derale Snap-In Radiator Adapter Fitting # D13035 is recommended when installing a transmission cooler on the 2010 Chevy Tahoe. I have linked a video featuring this fitting for you. In addition to the fitting and the core, # D52508, you will also need a bracket kit # D50020 to mount the cooler, hose clamps, # D13008, and about 10 feet of hose, # D15700. We also have a 25 foot length of hose, # D15799, if you want to err on the side of caution; especially if you are also installing a...
  view full answer...
• Engine Oil Cooler with Thermostat for a 2006 Toyota Tacoma with V6 Motor
  First you would need an engine oil cooler kit. I recommend # D15502 because it comes with multiple thread types and has the proper O-ring size for a V-6 Toyota motor. The sandwich adapter included is thermostatic so a separate thermostat is not required. Oil that is cooler than 180 degrees will bypass the heat exchanger, so your engine will warm up faster. You may need some extra hose like # D15700 for 10 feet. And for hose clamps use # D13008. I have included a couple of links to...
  view full answer...
• Parts Needed To Install a Derale High-Performance, Stacked-Plate Cooler on a 2015 Chevrolet Tahoe
  I do have an option for you but the part that you referenced, the Bracket Kit for Derale High Performance Stacked-Plate Coolers part # D50020 is just a bracket kit for a stacked-plate cooler like the Derale 25-Row, High-Performance, Stacked-Plate Cooler part # D52506. In order to use the above stacked-plate cooler you will need a few items which I have attached for you below but they will vary based on what size transmission lines your 2015 Chevrolet Tahoe uses. The most common is 3/8"...
  view full answer...
• Can I Bypass the Factory Transmisson Cooler on a 2007 Nissan Frontier
  We do not recommend bypassing the factory cooler with a supplemental transmission cooler, but if you are going to do so, I strongly suggest using the largest and most effective cooler that will fit in your engine compartment. Keep in mind, these transmission coolers are designed to be supplemental coolers to the vehicle's cooling system, not independent coolers. As far as coolers go, the most effective design is a stacked-plate cooler like the Derale High-Performance Transmission Cooler,...
  view full answer...
• Recommended Frame Rail Fluid Cooler for 200r4 Transmission on 1946 Chevy Truck
  The Derale 24" Frame Rail Fluid Cooler with -6 AN Inlets # D13225 is a great option. It does not require lines to the front of your truck to cool your transmission. There is not a longer option available, but you can run the Derale 17" Frame Rail Fluid Cooler with - 6 AN Inlets # D13221 as well if increased cooling is desired and you need to be under 45 inches. You may also be interested in the Derale -6 AN Female Swivel x 3/8" Barb Hose Fitting # D98200, Derale High-Temperature Replacement...
  view full answer...
• Larger Hose Fittings for Derale # D13611 on 2010 Mercury Mariner
  On the Derale Series 9000 Plate-Fin Transmission Cooler Kit w/ NPT Inlets - Class I -Extra Efficient # D13611, the fittings that come with the unit are 1/2" NPT x 3/8" hose barb. The other option for fittings are the Derale 1/2" NPT Male x 1/2" Barb Straight Hose Fitting - 2 Piece # D15712 along with the 1/2 inch inner diameter hose # D15700 and hose clamps # D13008. This slightly larger size is the only other option for the 1/2" NPT fitting on your cooler.
  view full answer...

Do you have a question about this Accessories and Part?