Parts Needed to Install 7-Way and Brake Controller on a 2006 international 4300

Question

Question:

I just purchased a 2006 international 4300. I’m needing to install a 7 way plug on the rear of the truck and also a trailer brake. What all do I need?

asked by: Shayne H

0

Expert Reply:

Hey Shayne, thanks for reaching out!

For wiring you need the Universal Wiring Kit # ETBC7 and then for a brake controller I recommend the Redarc Tow-Pro Liberty # RED24FR and Pigtail # RED69FR because this controller can be installed virtually anywhere and the control knob takes up minimal space.

If your turn and brake signals have their own circuits you'll also need the Curt Tail Light Converter # C59236 to get those functions combined.

expert reply by: Jon G

0

Answer 1

You'll need to use the #C59496 that you referenced to install first a 7-way on your dump truck and then to convert to a 7-way you'd just need the #37185 or if you plan to install a brake controller #ETBC7. For a controller the Brake EVN…

view full answer...

Answer 2

If your 2004 international 4300 has air brakes, then the brake switch (electrical) could be anywhere. But if it has regular hydraulic brakes then the switch should be located above the brake pedal. You would use a circuit tester like #PTW2993 to…

view full answer...

Answer 3

I've read that the red, brake pedal switch circuit on your 2007 4300 International Truck is not a 12 volt system. Another option you can use for the brake switch circuit is the CHMSL circuit if available. The white wire of the controller wiring…

view full answer...

Answer 4

If the brake pedal switch is not a 12 volt system on your 2006 International 4300 truck, another option would be to get the voltage from the the third brake light circuit. Sometimes this circuit is abbreviated as CHMSL. The reason you would not want…

view full answer...

Answer 5

Before you do anything else you will want to see if there is a brake switch above the brake pedal. If there is, then use a circuit tester such as #PTW2993 to test the wires. You are looking for one that only has power when you step on the brake…

view full answer...

Answer 6

When you are hardwiring a trailer brake controller like the Prodigy P2 #90885 the red wire connection that provides the triggering signal to the controller should be made to the wire on the COLD SIDE of the brake light switch circuit. This is the…

view full answer...

Answer 7

We may have a solution for you. To wire a brake controller on your 2007 International Trucks 4300 Series, you need to wire the controller's red wire to the stop light circuit. If the only wire you've found for brake lights is tied to the turn…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 12

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Parts Needed to Install 7-Way and Brake Controller on a 2006 international 4300

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching