Oval LED Reverse Lights with Grommet for Flatbed Trailer

Question

Question:

Reverse light for flatbed trailer - I am trying to match the style of my stop/ brake lights. They are oval shaped and held in with a grommet like this reverse light. But i want it in LED not incandescent. I cant find anything like that on the website. Can you point me in the right direction

asked by: Rob D

0

Expert Reply:

We have exactly what you are looking for in terms of an LED reverse light that fits with a grommet for your flatbed trailer. The Optronics LED Backup Light for Truck or Trailer - 6 Diodes # BUL12CB or the same light with 10 Diodes # BUL10CB can be mounted to your trailer with PVC Grommet for 6-1/2" Oval Trailer Tail Lights # A70GB and you will just need a 2-wire pigtail for the lights. For this you can use 2-Wire Pigtail # A45CB or Right Angle 2-Wire Pigtail # A49PB.

I have added links to video reviews of these reverse lights as well as a photo a customer sent in with one of these lights on his trailer so you can get an idea of how it will look.

expert reply by: Kyle S

0

click to enlarge

Answer 1

To connect back up lights you need to have a 7-way trailer connector on both your trailer and tow vehicle. On a 7-way the reverse lights are powered by the center pin. To connect reverse lights to the trailer's 7-way you can use 16 gauge wire…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 9

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Answer 10

Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity box.…

view full answer...

Answer 11

The Dexter Trailer Idler Hub Assembly for 3,500-lb Axles item #84545UC1-EZ fits a item #L68149 bearing which has a 1.378" inner diameter. I would not recommend using this hub on a boat trailer. Instead, you'll want a galvanized one like item…

view full answer...

Answer 12

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Oval LED Reverse Lights with Grommet for Flatbed Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching