See what our Experts say about this Optronics Accessories and Parts

• Replacement Boat Trailer Reverse Light for a Wesbar 203206
  Hey John, thanks for reaching out! The Wesbar 203206 has been discontinued and there isn't a direct replacement, but I have an alternative that will get the job done, you might just need to modify the cutout space a bit. The Optronics Backup Light # BU33CB is the closest thing I could find to what you have on your boat trailer. You're going to need the Grommet # A33GB as well as a 2-Wire Pigtail # A49PB to get everything installed. The light has 3 prongs, but only 2 are needed for your...
  view full answer...
• Looking for Way to Mount Optronics Backup Light # BUL10CB on Ranger Trail Boat Trailer
  In order to mount the Optronics Backup Light, # BUL10CB, on your Ranger Trail Boat Trailer, I recommend using the Rubber Grommet, # a70gb, and Trailer Light Mounting Bracket, # BK70BB. A wiring harness, part # A49PB for a right angle plug and part # A45CB for a straight plug, will also be needed for the Optronics Backup Light, # BUL10CB. I have included a few short videos for you to check out.
  view full answer...
• Brightness and Installation of the Optronics LED Backup Light # BUL22CB on a Boat Trailer
  I have attached a video demonstrating the brightness of the Optronics LED Backup Light, # BUL22CB, for you to check out. This light is waterproof and will work well on your boat trailer as a reverse light. Along with this light, you will want the Two Wire Pigtail, # A49PB. The end of this plug is molded rubber that, along with dialectic grease, will help seal the plug from water and moisture. To attach this light to your trailer, you will need the grommet, # A70gb. If you will not be...
  view full answer...
• Rewiring Boat Trailer for 7-Way to Use LED Lights
  There are a number of things you will need if you want to re-wire your boat trailer to use LED lights and you should start with Junction Box # 3375601100 and 7-Way # HM20041. Keep in mind you will also need Ring Terminals # 44-5310A and Loom Clamps # A0500 For LED lights I highly recommend checking out the LED Trailer Tail Light # STL57RB (Driver's side) and # STL56RB (Passenger's side). These are submersible lights with a total of 40 diodes and have mounting holes that are 2" center to...
  view full answer...
  
• LED Reverse Light Recommendation for 2005 Toyota Prius
  Since you have a Prius I would strongly recommend going with an LED reverse light that will draw considerably less than the Halogen part # PL-807. For that you'd want the LED light part # BUL10CB with the bracket # BK70BB and the grommet # A70GB and you'd have a setup that draws only .28 of an amp per light. You'll also need a wiring pigtail like the part # A49PB. This could be ran to the reverse light circuit of your vehicle without overdrawing it.
  view full answer...
• Recommended 5-3/4" Diameter LED Backup Light
  Hey Mark, thanks for the information! The LED Backup Light w/ Flange for Trucks or Trailers item # BUL11CBX is going to be the closest option I have to your specifications. This is a 5-3/4" diameter LED back up light that mounts in a 4-1/2" diameter cutout. It has three mounting holes spaced 4-7/8" apart center on center. You can use the Right Angle 2-Wire Pigtail item # A49PB or the 2-Wire Pigtail item # A45CB to complete the installation. Do you see any part numbers on your Optronics...
  view full answer...
• Recommended 6 Inch Oval LED Backup Light For Brightness
  We have 6-1/2 inch oval LED lights that are very bright, that are typically referred to as 6 inch lights in the trailer industry. I recommend the Optronics GloLight LED Backup Light for Truck or Trailer - Submersible - 22 Diodes, # BUL111CB, because it is a very bright replacement light that that meets the DOT compliant standards. They have a very clean look and are sonically sealed so they can handle all the weather thrown at them. They require a recessed mount # a70gb, and a 2-prong...
  view full answer...
• Replacement LED Marker Lights for Floe Pro 100 14 Foot Snowmobile Trailer
  From all the photos I saw online, it looks like Floe used grommet mounted 2-1/2 inch marker lights and standard 6-1/2 by 2-1/2 inch oblong taillights. If that's the case, for the amber 2-1/2 inch I would recommend # MCL59AB and # MCL59RB for the red marker light. The lamps use a standard # A55GB grommet to mount. The grommet is a fit for a 3 inch diameter rough opening. The lamps are designed to be used with a 2 pin pigtail like part # A49PB. I wasn't able to find a photo showing the...
  view full answer...
• Parts Needed to Add Back Up Lights & 7-Way Connector on Boat Trailer
  We can get you set up to add back up lights and a 7-way to your boat trailer, and I'll go over what you'll need. Let's start with the back up lights, and for your boat trailer you'll want submersible lights like you said, the GloLight LED Backup Light for Truck or Trailer - Submersible # BUL111CFPG. This will use a 2-wire (power and ground) pigtail, either the Right Angle 2-Wire Pigtail # A49PB or 2-Wire Pigtail # A45CB. Then for added wire I recommend 16 Gauge # 16-1-1, which is sold...
  view full answer...
• Brighter Trailer Tail Lights to Replace Bargman 92 Series Tail Lights
  There are brighter lights available for your current Bargman 92 Series lights, but none that have a reverse light function. So to replace your current lights with brighter LEDs you will need the LED Trailer Tail Light - Driver's Side # 328-003-81LM1 and LED Trailer Tail Light - Passenger Side # 328-003-81M1. That's the closest available for your mounting width, and I have added a link to a video install for you to check out. Additionally, you could just add separate reverse lights if...
  view full answer...
  
• Comparing Brightness Ratings of Optronics LED Tail Lights
  The Optronics LED Backup Light # BUL22CB is brighter than backup light # BUL10CB although I would not describe it as significant, though that can be subjective. Optronics measures the brightness of their lights using candelas and the # BUL10CB has a candela rating of 125, while the # BUL22CB has a candela rating of 160. There is also the backup light # BUL52CB which has a candela rating of 175. The reason I would not classify the brightness as significantly higher is because these lights...
  view full answer...
• Do Trailer Reverse Lights Require Two or Three Wires to be Powered
  Reverse lights like the part # STL211RCB only need power and ground to function. You would not need three wires ran to the light assembly. Power would need to come from the reverse light circuit of the tow vehicle but you can ground the lights to the trailer frame or using wire to run back to ground of the trailer wiring. The version of the light I would recommend instead though is the part # BUL10CB since this is just a reverse light. For pigtail harnesses you'd want either the # A45CB...
  view full answer...
• How Much Amperage Is Required to Add Reverse Lights to Trailer
  If the tow vehicle has a trailer reverse light circuit separate for trailer wiring then you'd be limited by the amperage rating of the fuse that protects it. If you are tapping into the reverse light circuit of your vehicle for the light then it comes down to the amperage rating of the fuse that protects the circuit as well as the amperage rating of the lights and how many amps are left over between those two numbers. Now with that all said if you went with an LED reverse light like the...
  view full answer...
• Reverse or Utility Lights to See When Backing Up Cargo Trailer
  If your trailer has a 7-Way connector and the vehicle side has the center pin active when the vehicle is in reverse then you can install backup lights on the trailer and wire them to the center pin. You can use 2 of backup light # BUL12CB 2 of grommet # a70gb 2 of bracket # BK70BB And 2 of pigtail # A49PB If you do not have a 7-Way but just a 4-Way instead you could wire a utility light such as # TLL48FB in with the running light wire on the trailer and have the utility light run on a...
  view full answer...
• Oval LED Reverse Lights with Grommet for Flatbed Trailer
  We have exactly what you are looking for in terms of an LED reverse light that fits with a grommet for your flatbed trailer. The Optronics LED Backup Light for Truck or Trailer - 6 Diodes # BUL12CB or the same light with 10 Diodes # BUL10CB can be mounted to your trailer with PVC Grommet for 6-1/2" Oval Trailer Tail Lights # A70GB and you will just need a 2-wire pigtail for the lights. For this you can use 2-Wire Pigtail # A45CB or Right Angle 2-Wire Pigtail # A49PB. I have added links...
  view full answer...
  
• Recommended Oval LED Lights and Brackets for Flat Bed
  For your flatbed setup, I recommend starting with the brackets # BK70BB. Then I recommend using the PVC Grommet for 6-1/2" Oval Trailer Tail Lights # a70gb to hold the lights in the bracket. For the red led lights I recommend the Optronics LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 10 Diodes - Red Lens # STL72RB with wiring pigtail # A47PB. For the white led lights I recommend the LED Backup Light for Truck or Trailer - Submersible - 10 Diodes - Oval - Clear Lens - Qty...
  view full answer...
• Outside Diameter of 2 Inch Round Grommet
  The outside diameter of the 2" Round Grommet # A54GB you referenced is 2-3/4". This grommet is used with 2" round lights such as the GloLight LED # MCL155RB (Red) or GloLight LED # MCL155AB (Amber). You will also need a 2-wire pigtail to complete the installation of these lights; either # A46PB for a 6" lead or # A49PB for a 10" lead. I have added links to video reviews of these parts for you to check out.
  view full answer...
  
• How Does Backup Light of Fusion LED Trailer Tail Light Work
  In order to utilize the backup light function of the Fusion LED Trailer Tail Light # STL211RB you will need to plug in a 2-Wire Pigtail, either part # A45CB or # A49PB for a right angle pigtail. You can see from the accompanying photo of the rear of this light that it has connections for both a 2-wire and 3-wire plug. This would need to be used along with the 3-Wire Pigtail # A45PB or # A47PB (right angle) which gives the light its tail light functions. I looked up your order from the...
  view full answer...
  
• Recommended Bright Back Up Light For A Utility Trailer
  The Optronics LED Trailer Utility Light - Submersible - 3 Diodes # UCL55CB will be 15 lumens, so it can work as a back-up light, but it will not be very bright. However, the Optronics Miro-Flex LED Utility Light - Submersible - 9 Diodes # UCL50CB will measure almost exactly the same (2" diameter x 1-3/16"), but as it has 9 diodes it will be 44 lumens. This is the light I would go with. If you do not already have them, the Right Angle 2-Wire Pigtail # A49PB and 2" Round Grommet # A54GB...
  view full answer...
  
• Brightest LED Backup Lights Available That Fit Oval Hole On Trailer
  The GloLight LED Backup Light for Truck or Trailer # BUL111CB that you mentioned is going to be your best option if you are looking for the brightest backup lights in the oval recessed mount style. This product does not offer specs for lumens; I did contact Optronics to verify. They did, however, confirm with me that this LED backup light is going to be the brightest one available. It has 22 diodes, which is more than any other light in this configuration/style. This is DOT compliant. The...
  view full answer...
• Plugs Needed for the Fusion LED Trailer Tail Light # STL211RCB
  At first I thought that this light had 2 places for the 3 terminal plugs but if you check out the attached picture of the Fusion LED Trailer Tail Light # STL211RCB you can see that one plug has 3 prongs (for tail light functions) and one plug has 2 prongs (for reverse light function). If you are just needing standard plugs then you would use part # A45CB for the 2 prongs and part # A45PB for the 3 prongs. These are also available at right angles with parts # A49PB and # A47PB respectively.
  view full answer...
  
• What Two Pigtails do I Need for my Fusion LED Trailer Tail Light Part # STL211RB
  For the Fusion LED Trailer Tail Light - Stop, Tail, Turn, Backup part # STL211RB you will use the Right Angle 3-Wire Pigtail for Optronics Trailer Lights part # A47PB for the three wire which will carry your running lights, turn/brake signal lights and your ground and the Right Angle 2-Wire Pigtail part # A49PB for the reverse light. I have linked a video for you on the installation process so you can see how they will work together.
  view full answer...
• Adding Extra LED Reverse Lights to a 2015 Subaru Forester
  I recommend using LED back up light # BUL10CB which is actually DOT approved as a backup light. With it I recommend grommet # a70gb, mounting bracket # BK70BB, and wiring harness # A49PB. On the wiring harness the white wire is the ground and will attach to a clean, bare metal surface. The red wire is for power and would need to be spliced into a reverse light wire behind a tail light on your 2015 Subaru Forester. You will need to attach the new light red wire to a longer strand of wire...
  view full answer...
• Brightest Round LED Backup Trailer Light
  The Light Guide LED Backup Light # BUL603CB you referenced is certainly a nice, bright LED backup light, but the brightest is the GloLight LED Backup Light for Truck or Trailer # BUL101CB, as you can see by the accompanying photo. This light requires Grommet # A45GB and Right Angle 2-Wire Pigtail # A49PB. This does come packaged together with the GloLight LED Backup Light w/ Grommet and Pigtail # BUL101CKB. I have added links to video reviews for you as well which I highly recommend...
  view full answer...
  

Do you have a question about this Accessories and Part?