Correct Size Nuts and Washers for Electric Brake 23-26 Assembly

Question

Question:

What size are the nuts and washers for the 10 brake assembly?

asked by: Bill G

0

Expert Reply:

The 10 inch Electric Brake Assembly, # 23-26, requires a 7/16 inch, fine thread bolt for installation. Use part # 6-17 for installation. The lock washer is also 7/16 inch. Part # 5-8 is the correct washer for this application.

expert reply by: Michael H

0

Answer 1

The Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3,500 lbs part #AKEBRK-35 may be the assemblies you need based off the weight capacity of 3,500 lbs. To be sure you want to make sure your existing assemblies are 10"…

view full answer...

Answer 2

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 3

In some cases trailer lighting will ground through the hitch ball but that's typically only if the actual ground circuit is insufficient. This is not an ideal setup. It needs to ground through the wiring of the trailer harness. You can test this…

view full answer...

Answer 4

A Lippert 3,000 Lb (LCI35) Trailer Axle will use the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles - 3,500 lb with #84 Spindle part #BK2-100 which has everything you need from the bearings to the seals.

view full answer...

Answer 5

Hey Steve, Did you happen to check for power while the vehicle was running? While uncommon I have seen some vehicles with power only while the vehicle is running. Usually if the 12v pin on your trailer connector is not getting any power it is due to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Correct Size Nuts and Washers for Electric Brake 23-26 Assembly

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching