Correct Bearings for LCI35 Lippert 3,000 Lb Trailer Axle

Question

Question:

What would the bearing kit be for this axle? I have ~ 35000 miles on the trailer while I have kept them clean and greased its probably time to replace them

asked by: Steven Y

0

Expert Reply:

A Lippert 3,000 Lb (LCI35) Trailer Axle will use the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles - 3,500 lb with #84 Spindle part # BK2-100 which has everything you need from the bearings to the seals.

expert reply by: Conner L

0

Correct Bearings for LCI35 Lippert 3,000 Lb Trailer Axle
(click to enlarge)

Answer 1

No, they do not require lock washers. The torque specs for the 9/16" diameter U-bolts item #APUBR-9 is 65-95 ft lbs. With that amount of torque on the nuts they would not back off. What kind of trailer do you have?

view full answer...

Answer 2

The retaining nuts like what comes with the part #RG05-100 that you referenced can be reused.

view full answer...

Answer 3

I have an axle that is pretty close to what you're wanting, but is not going to work as the spring center measurement is a bit off and it needs to be just right to work. I do have a solution though. You can get the Timbren Axle-less Trailer…

view full answer...

Answer 4

I was able to track down a wiring diagram of the Atwood Water Heater Relay 93849 which I have attached for you below.

view full answer...

Answer 5

Hey Perry, thanks for reaching out. We certainly should have the parts you need for an oil bath conversion, but I will need to collect a bit more info on your axle in order to be sure you get the right parts. First I will need to know the weight…

view full answer...

Answer 6

Hello Jacques, thanks for reaching out. Yes, you can put just one MORryde X-Factor Crossmember #MR33WR on the center hanger for starter. MORryde does recommend doing all 3 for optimal support, but it is perfectly acceptable to start with just one as…

view full answer...

Answer 7

Those are some good options, and the best overall upgrade (without getting too crazy like you said!) for your Jayco with tandem 3,500 lb axles is going to be the MORryde CRE3000 with the X-factor crossmember. The Road Armor is good, but the…

view full answer...

Answer 8

We have exactly what you are looking for. I reached out to my contact at Lippert and based on the information on the axle tag you provided your 8000lb axle uses the following replacement parts: Inner bearing: #25580 Inner race: #25520 Outer bearing:…

view full answer...

Answer 9

The Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3,500 lbs part #AKEBRK-35 may be the assemblies you need based off the weight capacity of 3,500 lbs. To be sure you want to make sure your existing assemblies are 10"…

view full answer...

Answer 10

In some cases trailer lighting will ground through the hitch ball but that's typically only if the actual ground circuit is insufficient. This is not an ideal setup. It needs to ground through the wiring of the trailer harness. You can test this…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

To replace the bearings on a Lippert 3,500 lbs axle you will need the outer bearing item #L44649 inner bearing item #L68149. We do have a kit that has the necessary races, seals, and bearings. It is the Hub Bearing Kit for Lippert, Dexter, and Al-Ko…

view full answer...

Correct Bearings for LCI35 Lippert 3,000 Lb Trailer Axle

Product Page this Question was Asked From

Continue Researching