Is The Replacement Shock for Demco Hydraulic Trailer Brake Actuators DS12426 An OEM Part?

Question

Question:

Is this an OEM part?

asked by: Nick

0

Expert Reply:

Hey Nick, thanks for reaching out. Yes, the Replacement Shock for Demco Hydraulic Trailer Brake Actuators # DS12426 is an OEM part we get directly from Demco. It'll replace the shock on the model DA91,DA10, DA16, and DA20 actuators.

What actuator do you have?

expert reply by: Jesse M

0

Answer 1

Happy to help Jennifer, The screw caps are included with TecNiq Low Profile Stop Tail Turn Light #TN42TR, but the mounting hardware is not. You'll need to source two #8 mounting screws locally. Most hardware stores carry them and you can choose…

view full answer...

Answer 2

Thank you for the image of your setup Steve. I do not know what the manufacturer was thinking when they welded in the Demco Actuator on your boat trailer. With how it was installed there is no way for you to access that rear pin without drilling a…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Is The Replacement Shock for Demco Hydraulic Trailer Brake Actuators DS12426 An OEM Part?

Product Page this Question was Asked From

Continue Researching