Best Way To Mount A 4-Flat Plug On The Back Of A 2026 Ford Bronco
Updated 08/06/2026 | Published 07/29/2026
Question:
I just bought and installed, the C76WR Curt Trailer Hitch Receiver - Custom Fit - Class III - 2 I also have working harness but don’t know how to mount its bracket onto the Bronco. Could you help me please?
asked by: Tj D
Expert Reply:
Hey TJ, thanks for reaching out. The best way to mount a 4-flat plug on the back of your Bronco is with the Curt Mounting Bracket for 4-Pole Flat Trailer Connector # C42CR. You'll need to mount it to the bumper so what I recommend is using a few bolts, washers and nuts to attach it to the bottom of the bumper next to the receiver.
I've included a picture showing what that will look like once its done.
What kind of trailer do you plan to tow?
(click to enlarge)
Willias M.
8/6/2026
Hi TJ, On my 2023 Tucson I installed the Curt Mounting Bracket for the 4 pole flat connector to the left of the hitch receiver to the bottom flat part of the thick plastic molded rear bumper which hides the hitch receiver for the most part. I used 2 small stainless phillips 3/4 inch long screws with nylon inserted locking nuts. It looks professionally installed, very solid and works great. Hope this helps. William
Product Page this Question was Asked From
Curt Mounting Bracket for 4-Pole Flat Trailer Connector
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 4 Flat
- CURT
more information >
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Video: etrailer Class III Trailer Hitch Step-By-Step Install - 2026 Ford Bronco
- Shop: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Q&A: Difference Between Curt and Draw-Tite Hitch for 2024 Ford Bronco
- Search Results: accessories and parts
- Search Results: plug only trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: wiring harness bracket
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Shop: TowSmart Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Mounting Bracket for 4-Way and 7-Way Connector Plug
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Q&A: Recommended Trailer Hitch and Wiring Harness for a 2022 Ford Bronco
- Q&A: Correct 4-Way Trailer Wiring Harness For 2024 Ford Bronco
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Clean Up Your Trailer Wiring
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Search Results: trailer jack
on Accessories and Parts
Cj K.
8/5/2026
Hey TJ i used some JB Weld metal epoxy to glue it right on top of my hitch. It worked out great just make sure you set it up to plug in and pull out to the side of the vehicle. i did not like the option to bolt it the plastic bumper.