Looking for Replacement Grand Design Aluminum Phoenix Trailer Wheel

Question

Question:

Will the TA95ZR replace a Grand Design 140180 ST215/75R17.5 LRH COOPER WORKSERIES RADIAL TIRE 17.5X6.75-8-6.5 with 0inch off set and 4.9inch pilot diameter?

asked by: Megan C

0

Trailer Wheel
(click to enlarge)

Expert Reply:

Hey Megan, I think we can still help but the # TA95ZR is a hub piloted wheel and it's pilot diameter does not match what you have now so it would not work for you. Instead we have the exact replacement wheel to what you sent in a picture of and described with the Lionshead part # LH88VR. Did your wheel get damaged and you need a replacement or are you looking for a spare?

expert reply by: Jameson C

0

Megan C.

2/16/2026

I am looking for a spare wheel and tire set up that would be able to replace the Grand Design info I attached previously.

Jameson C.

2/16/2026

@MeganC Is your wheel hold on with lug nuts or lug bolts? Reason I ask is I want to find out for sure whether you currently have a lug centric or hub centric wheel/tire currently.

Megan C.

2/17/2026

@JamesonC it is held on by lug nuts

Jameson C.

2/17/2026

@MeganC that's a good sign. That means that the pilot diameter does not need to be exactly the same since the lug nuts are what centers the wheel. The lug nuts are tapered right?

See All (7) Replies to Megan C. ∨

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Looking for Replacement Grand Design Aluminum Phoenix Trailer Wheel

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching