Does TowSmart Trailer Hitch Receiver Interfere With Spare Tire On 2025 Kia Telluride?

Question

Question:

Will the TowSmart hitch interfere with the spare tire under my 2025 Kia Telluride?

asked by: Steve

0

Expert Reply:

Not at all, Steve - the spare tire goes right back into its original position once the TowSmart # TS84ZR is installed. The design allows full clearance for the tire and hoist cable.
You’ll lower the spare temporarily for installation, then reinstall it afterward with no issues.

If you plan to tow, grab the Curt Wiring Harness # C93FV for LX or S trims without LED taillights or # C29ZV for higher trims. Pair that with the Ball Mount Kit # 989891, and you’ll be ready to hit the road safely.

Are you setting it up for a camper or maybe a small utility trailer?

expert reply by: Andrew N

0

Kia Telluride hitch install with spare tire
(click to enlarge)

Steve

11/26/2025

Good to hear it clear. I really didn’t want to mess with the spare setup. Sounds like this is the way to go. Thanks for the help!

Andrew N.

11/26/2025

@Steve You bet, Steve! A lot of people worry about that, but TowSmart did a nice job keeping everything tucked up where it belongs. If you end up towing later, just grab the wiring harness and ball mount kit we talked about. Safe travels, and feel free to circle back if you need anything else!

Answer 1

Welcome back Frank! To add a 7-Way connector and brake controller to your 2024 Kia Telluride, I recommend the following parts: 7-Way Connector - Universal Installation Kit for Trailer Brake Controller item #ETBC7 Brake Controller - Redarc Tow-Pro…

view full answer...

Answer 2

To install a 7-Way connector on your 2024 Kia Telluride you will need two separate wiring harnesses because they don't make just one that'll do the job. The first harness you'll need is the Curt T-Connector Vehicle Wiring Harness item…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yeah, it is definitely a bit to sort through, so I think we can help you out with the right 4-way wiring harness for your 2024 Kia Telluride. We'll start with the easy one, which is if you want to hardwire a 4-way, the model of your Telluride…

view full answer...

Does TowSmart Trailer Hitch Receiver Interfere With Spare Tire On 2025 Kia Telluride?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching