Possible Hitch to Fit 2010 Ford E-450 Thor RV Application

Question

Question:

Will this receiver fit my 2010 Ford E-450 Thor RV? It is a Ford cutaway with an installed Reese receiver 3,500 lbs rating. I am planning on towing a Jeep Wrangler, so the rating needs to be at least 5,000 lbs. If not, what hitch would be recommended? Thanks.

asked by: Bob

0

Expert Reply:

If the bolt holes on the frame of your 2010 Ford E-450 RV are 38-5/8 inches apart from left to right the # 14055 can fit but the hitch you referenced has not been confirmed as a fit so I would not recommend it.

expert reply by: Jameson C

0

Answer 1

Hi Daniel! We do have a hitch for your 2008 Ford E350 cutaway with an enclosed utility bed, but it may not be a custom fit option. If your bolt holes are 38-5/8 inches from frame to frame and the utility bed doesn't sit lower than the standard…

view full answer...

Answer 2

The distances of the mounting holes for the Curt Trailer Hitch Receiver #14055 are 38-1/4" for the rearmost holes and then 38" for the forwardmost (towards the cab) holes. I have attached a dimensional photo for you to check out. Please…

view full answer...

Answer 3

For your 2014 Ford E-350 cutaway chassis the Curt hitch part #14055 would be an excellent option. I attached a picture that shows it sticks out a decent amount from the rear of the frame as well.

view full answer...

Answer 4

There are several Curt and several Draw-Tite hitches available for a 2009 Ford E-250, depending on which model E-250 you have. Is your van a Superwagon? How much weight are you needing to pull? This information will help narrow down the hitches that…

view full answer...

Answer 5

Curt Class IV hitch #14055 has mounting holes on its flanges that are indeed spaced at 38-1/4-inches apart measured on the hole centers. The overall width of the hitch, measured outside edge to outside edge at the mounting flanges, is 40-inches.…

view full answer...

Answer 6

The Curt #14055 will actually sit just about flush with the edge of the bumper once installed on your 2006 Ford E-350. Though this will meet the weight capacities you need, if you are looking for something to completely clear the bumper, it will fall…

view full answer...

Answer 7

The distance between the mounting holes from side to side on the Draw Tite trailer hitch part #41945 are 38-1/2 inches. This hitch fits the following vehicles: 2004 - 2014 Ford Van E-150 2004 - 2014 Ford Van E-250 2004 - 2014 Ford Van E-350 2000 -…

view full answer...

Answer 8

As long as your rear bumper looks the same as the one I have attached a photo of, the Draw-Tite Ultra Frame Trailer Hitch Receiver part #41945 will fit and work well for your 2011 Ford E-350. This is a Class V hitch with a 2" receiver tube…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Possible Hitch to Fit 2010 Ford E-450 Thor RV Application

Products Featured in This Question

Continue Researching