Do I Need to Remove the Identification Light Bar to Replace the Lights?
Updated 10/13/2025 | Published 10/06/2025 >
Products Featured in This Question
Question:
Hello, I have light bar MC97RB and need to replace a single LED that went out. The video refers to single LED MC95RB to use as replacement. My question is if this is replaceable from the front of the light bar or if I need to remove the light bar from and replace it from the back-side? This light bar was riveted on to my trailer not screwed, so hoping I can replace the LED without removing it from the trailer. I appreciate your support!
asked by: Kevin
Expert Reply:
Hey Kevin. The Optronics Mini Trailer Clearance or Side Marker Light item # MC95RB installs with two mounting screws on the rear of the light. You will need to remove the Identification Light Bar item # MC97RB to access these screws. I attached a picture below so you can see the back of that light bar.
What kind of trailer do you have?
Product Page this Question was Asked From
Identification Light Bar for Trailers over 80" Wide - Submersible - Silver Base - Red
- Trailer Lights
- Clearance Lights
- Marker
- Light Bar
- Surface Mount
- Submersible Lights
- Incandescent Light
- 14-1/4L x 1-3/16W Inch
- Red
- Optronics
more information >
Continue Researching
- Shop: Trailer Wiring
- Shop: Identification Light Bar for Trailers over 80" Wide - Submersible - 9 LEDs - Silver Base - Red
- Shop: Identification Light Bar for Trailers over 80" Wide - Submersible - Silver Base - Red
- Shop: Identification Light Bar for Trailers over 80" Wide - Submersible - 9 LEDs - Silver Base - Red
- Shop: Optronics Mini Trailer Clearance or Side Marker Light - Submersible - Incandescent - Amber Lens
- Shop: Self-Tapping Screw - 1/4" -14 x 3/4" Long - Zinc
- Q&A: Can The Bulb Be Replaced On The Optronics Mini Trailer Clearance or Side Marker Light MC95AB?
- Search Results: trailer lights
- Search Results: self tapping screw
- Search Results: screw
- Video: All You Need to Know About the Self-Tapping Screw
- Shop: Optronics Mini Trailer Clearance or Side Marker Light - Submersible - Incandescent - Red Lens
- Shop: Optronics LED Trailer Clearance or Side Marker Light - Submersible - 3 Diodes - Rectangle - Red Lens
- Q&A: Difference Between the MCL97RB and MCL97RPG Optronics Identification Light Bars
- Video: Ultimate Overview of the Identification Light Bar for Trailers over 80" Wide
- Video: Identification Light Bar for Trailers over 80" Wide Spec Review
- Search Results: butt connectors wiring
- Search Results: heat shrink butt connector
- Search Results: accessories and parts
- Search Results: trailer wiring
- Q&A: Replacement Passenger Side Tail Light for Sun Tracker Trailer
- Q&A: Identification Light Bar for Trailers over 80" Wide that Grounds Through the Mounting Hardware
- Video: Complete Breakdown of the Identification Light Bar for Trailers over 80" Wide
- Video: LED Identification Light Bar for Trailers over 80" Wide: The Breakdown
- Q&A: installing New Light Bar With Only One Wire On Boat Trailer
- Video: Feature Review Optronics Mini Trailer Clearance or Side Marker Light
- Q&A: Replacement Light for Identification Light Bar MC97RB
- Q&A: How To Hook Up the Identification Light Bar MCL97RB To a Two Wire Plug
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams



Kevin
10/12/2025
Hi Jerred, Thanks for the reply! I have a trail master boat trailer SR2041BR. I'm not sure if this is an original fixture or if the previous owner installed it. I purchased 2 of the self-tapping screws you guys sell with for these light bars. I'll try to drill out and remove the rivets and use them. Thanks! -Kevin