What is Blue Piece For Optronics Identification Light Bar

Question

Question:

Installing bar light on boat trailer product MCL97RK. In the package is a blue plastic and metal piece. Video of product doesn’t address what it is use for. How do I use it?

asked by: Frank

0

Expert Reply:

Hello Frank,

Thanks for the purchase and the blue piece of the Identification Light Bar for Trailers over 80" Wide - Submersible - 9 LEDs - Silver Base - Red # MCL97RB is a quick splice.

expert reply by: Kyle S

0

Answer 1

Yes, the only difference between these light bars is that the #MCL97RPG has the 0.180 male bullet at the end of the wire and the #MCL97RB just has a regular wire you'd use a butt connector like part #DW05744-5 for the installation. Other than…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The torque requirements for leaf spring u-bolts depend on the diameter of the u-bolts that are being used. If the gross weight of your tandem axle trailer is 7,000 lbs, then you likely have two 3,500 lb axles. Typically 1/2 inch diameter u-bolts are…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The determine the correct replacement leaf spring on your 2021 Coachmen 259FKDS you'll need to lift your trailer frame so the spring is hanging freely and then measure from center-eye to center-eye, then for the equalizer you need to measure…

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

Hey Thomas, the most important factors for picking out a replacement leaf spring for a trailer are matching axle capacity and length. Getting the same amount of leaves in the spring pack is actually not a huge priority so I wouldn't worry too…

view full answer...

What is Blue Piece For Optronics Identification Light Bar

Product Page this Question was Asked From

Continue Researching