E-Track System For Enclosed Trailer Walls

Question

Question:

Do you sell the E-trac Strips to bolt along the walls of a Cargo Trailers, so i can clip straps to hold things in place.

asked by: Ralph B

0

Expert Reply:

We do offer E-Track Trailer Cargo Control that will work on the floor of a trailer and also will work on the wall of an enclosed trailer.

For the vertical E-Track channels typically used for walls you can order part # E19146. These are sold individually and are available in 4 foot sections.

If you are interested in the tracks that are normally mounted to the floor for securing cargo, you can order part # E19148. these are available in 5 foot long sections.

To cover the end of the E-Track I recommend the Plastic End Cap, part # ET8730.

I have attached links to a couple of installation videos for the E-Track systems you can check out. And I have also attached a link to our product page that has several items that work with the E-Track system you may want to take a look at.

expert reply by: Jeffrey L

0

Answer 1

E-tracks are typically the stronger of the two, but X-track is more versatile since you can mount them horizontally or vertically. Choosing between the two really depends upon how you plan to use them. If you are installing something in a truck bed,…

view full answer...

Answer 2

No long-term contract, Natalie - but a service plan is required to use the trackers. When you buy the 3000 with wifi assist #PM84FR, 5000 #PM64FR, or 5000 with wifi assist #PM74FR from etrailer, you’re purchasing the hardware/device only. To activate…

view full answer...

Answer 3

Since the slot dimensions and capacity of different brands of E-Track are identical, really the only differences are the finish and the lengths the tracks are sold in. If you're using the E-Track in an area where aesthetics are important, you can…

view full answer...

Answer 4

Hey Deven, thanks for reaching out, and good question. For a 12 volt system, the charge controller can handle one 200 watt panel. For 24v systems it can do two 200 watt panels. So while the kit technically is expandable, with your 12v system, the one…

view full answer...

Answer 5

Having the factory fuse is perfectly fine for an aftermarket brake controller. The benefit of a circuit breaker is that it can reset itself so you do not have to replace a fuse should it blow. So you are good to go with the 30 amp factory fuse…

view full answer...

Answer 6

Yes, you can use Erickson Horizontal E-Track item #E19148 as front straps to hold down a car. These tracks have a 2,000 lbs maximum capacity per track. You will want to use the etrailer E-Track Backing Plates w/ Hardware item #e96RR for mounting. The…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Kirt, Congrats on the new car! To get your car safe to flat tow you'll need the following parts: Base-Plate #RM39FR Tow-Bar Adapter #RO64FR Lighting #RM-15267 Chargeline #RM-156-25 Air-Force One Vehicle Side #SM99209 and Hose #SM99666 (if you…

view full answer...

Answer 10

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

E-Track System For Enclosed Trailer Walls

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching