Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Nothing ruins a setup faster than a wobbly camper. These Ark Drop Down Corner RV Stabilizer Jacks lock your frame solid so you can move around without feeling every step. The swiveling legs drop straight down or angle out to fit uneven spots, giving you flexibility and a firm stance every time you park. Once welded in place, they take the sway out of walking, loading, or unloading gear so everything feels steady and secure.
Vibration and rattle might seem small, but over a whole weekend they get old fast. Each jack has silencer pads that cut down noise caused by vibration, plus a locking swivel bracket that keeps the leg firmly in place once lowered. The big grip handle gives you control when rotating the leg into position so you can lock it down smoothly without fighting stiff hardware or loose pivots.
Setting up on grass or gravel doesn’t have to mean sinking or shifting overnight. The large flat feet spread out the weight of your camper so every corner stays planted. They perform well on soft ground where smaller feet would dig in or tilt, keeping your setup level and stable until it’s time to pack up again.
Outdoor gear takes a beating from weather and road grime, but these jacks are built to handle it. The steel body is finished with a black powder coat that’s corrosion- and rust-resistant with a 600-hour salt spray rating. That means season after season of reliable performance without worrying about rusted joints or seized parts from exposure.
Raising and lowering each jack is straightforward thanks to the included winding handle that makes dispatching the steadies simple.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Michael: Hi there. I'm Michael with etrailer.com. Today we're going to take a quick look at the Ark Drop Down Corner RV stabilizing jack kit. This kit is going to come with two of these jacks, as well as a winding handle to raise and lower them. These jacks are stabilizer jacks so they're going to allow your chassis to move less. Once you get to your destination, you'll lower these down, and they'll give you a little bit more stability for your camper so that you're not having that rocking sensation as you're moving around in your camper.
These are not designed to lift any weight, so they're not going to be lifting jacks. So keep that in mind, make sure that you're getting the right jack for your needs.These jacks are really nice. One thing I like about them, they have these nice wide feet so even if you are setting up on soft earth, they're not going to sink in. They're about 6" wide by about 6" tall, so nice wide foot there. They do pivot so even if you are setting up on un-level ground, these will accommodate so that you always have sure footing there.
As far as our height goes, when we have it fully retracted like it is now, it sits about 16 and a half inches. So pretty compact, easy to transport. And then when we have it fully extended it's right about 24 and a half inches. It's right about 2ft in total height so you can see the difference between our extended and retracted options there. As far as getting these mounted in place, it's going to be very...
there's a lot of options for you.So this plate up here that I'm going to take off real fast, this is your weld-on plate. It's connected with these long bolts. This can be welded onto the chassis of your camper. That way, if you ever need to take the jack off, if something we're to.. one of the components we're to fail or something, you need to replace the jack, you can just remove those bolts and remove the jack from that weld-on plate.
You won't have to worry about breaking your welds or anything like that. Alternatively, if you don't like welding, you can just discard this weld-on plate and then drill a couple of holes in the top of the jack there and bolt this in place. So either option will work. Just a matter of preference, up to you which one you prefer. But once you have this plate where you want it, it is very easy to put these bolts back in and get those nuts on the end. They tighten down with a 13mm wrench and socket.Another really nice feature is this adjustable mechanism here. So it's got a nice wide handle, very easy to grip, and then you simply pull back on it. It's spring-loaded so those pins will disengage and it will allow this head to pivot. There's multiple locations that it can lock into to maximize the angles that you're working with. But then when you want to retract it, put it away, it will sit up there like that. So once you have this welded in place, this will be sitting parallel to your chassis. So it will sit up nice and tight. And you can see that our foot here does automatically drop down like that. But as you're traveling down the road, it might bounce around a lot. One of the nice features of this, you can close the handle to get access to your port here. And if you retract this enough it will lock that foot in place so that it's not going to wobble around and move. I could actually probably tighten that down just a little bit more.But you also have these pads on either side that are going to help prevent that metal-on-metal contact. So even if this is just a little bit loose, it won't make as much noise. So that will help as we're traveling down the road, not having to worry about the noise that's rattling around down there because there won't be any. This does have a black powdercoat finish to it. So it's going to be nice and rust and corrosion-resistant. So it should do a good job, hold up well for a long time. And this handle is very easy to use. Just as you've seen me do, just get it in place there. It's got a twisting knob on the end and then a grip here in the middle. So very easy to extend our jack and retract it again.So if you're looking for a stabilizing jack set I'd say this is going to be a great option for you. It's got a lot of nice features to it and the weld-on plate or bolting-on option should fit for just about any application out there. So that's going to complete our look for today. This set is the 2ft set. There is a slightly larger set as well that we have available here at etrailer.com. So if this isn't going to extend as far as you need it to I'd recommend you checking that one out, it might better suit your needs. So that's going to complete our look for today. Thanks for watching. Again, I'm Michael with etrailer.com and we'll see you next time.
Customer Satisfaction Score:
93% were satisfied with this product
7% of customers were not satisfied
Ratings & Reviews
Great thank you exactly what I needed.
Had one of the two jacks fail to extend more than 2" from start? Other jack works fine! Only stableizing 1800 lbs. I need only one replacement.
The Jacks were delivered on time, will not hesitate do buy again from etrailer.com.
These initials came with rust and had to be replaced.
They are absolutely useless when vertical, but are half decent when extended to the side (only for side to side movement, still a ton of play for front to back movement). I would not recommend.
Installed these on my pop up trailer, so much easier to use than original jacks!
These jacks work exactly like they should. I think it was a very good investment for my 34 foot bumper pull camper. Highly recommended!
Jack is really strong much better than I figured
Def has a down side of very hard to release and drop down
I can hardly do it sometimes and no way my wife can
Absolutely needs to be more user friendly in that aspect
Love the stabilizer operation style. Would like to see a slightly shorter one as the required clearance needed to swing down at some camp sites is difficult
Great product but… VERY poorly packed for shipping! Both of my shipments were delivered falling out of the cartons. If these weren’t so bombproof, they would of been destroyed. Only 1 of the four I ordered was bent at delivery.
Arrived early....fast shipping. Was double boxed so product was well protected. Will be installing them on my RV soon. Trial fit looks like they will work excellent.
Great product, welded the mounts to the front rails of the trailer and was easy to use. Took the weight off the hitch lift. A driver tried to drive off and forgot to raise the stabilizers and damaged them badly. Replacements were easy to attach to the welded mount. We are back in operation.
Product works great. Any 3/4 inch socket can raise and lower the jack. Fully adjustable from vertical to ground to perpendicular and many stops in between. They can rotate to work on left or right side. I drilled and bolted them on. No problem.
The item arrived on time, and the customer service was great.
Easy install, work perfect. E-Trailer was very helpful, fast delivery, best price.
Randy
6/6/2025
After 1 year still works like new. No rust, powder coat in fantastic. Excellent addition to stability of our camper.
Great product. Seem to be very well made
Very happy with the jacks
These stabilizers are exactly what I needed for a class C camper. Installation was exactly like your tech video described. Etrailer is awesome, thanks!!
We had these installed on our trailer and used them on a five-state trip over three weeks. I love how easy they are to use and the stability. My only drawback is which size to use. A shorter version would work better that the 22 inch version i bought. In some areas it was too tall to go vertical in rough terrain or sloping KOA spaces I'm glad the company includes a 45 degree lock in setting so we were able to use that option on ours.
These are incredible! I have a teardrop camper that came with "scissor" type stabilizers, and they almost immediately broke. They were very difficult to raise and lower and I needed an impact drill to make them work, only weeks after delivery. Unfortunately the company went out of business and I was forced to find my own solution. eTrailer.com to the rescue!
I bought 2 sets so I could have one on each corner of my Teardrop Camper. I got them welded locally for just over $300, and couldn't be happier. These drop down straight with just a bit of ground clearance. Although the primary purpose is stabilization, I could use these to jack up the whole side of my camper to change a tire now. No more going underneath and jacking it up manually anymore. I love how they can be set at an angle or straight up and down. My only question is why didn't the builder of my camper put these on in the first place! If I am going to have stabilizers that are used every time I go out, why not have the best? Love these, highly recommend.
Gregg M.
10/21/2025
After a year, my original review stands. Get these, you wont regret it.
Do you have a question about this Camper Jack?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Katrina B.
8/4/2022
I have gotten in contact with the manufacturer and they have confirmed that there is a one year warranty on this item. I have sent your information over to our customer service department for them to assist you in this.