Replacement Jack Or Rebuild Kit For Jack On A 2015 Big Tex Tilt Trailer
Updated 07/15/2025 | Published 07/09/2025
Products Featured in This Question
Question:
I have a 2015 big tex 14TL TILT TRAILER.l need rebuild kit or new jack. I think its a Ram 4in. Square jack.
asked by: Mike J
Expert Reply:
Hi Mike!
We do have the Replacement Rod and Nut for Ram Square, Direct Weld Jacks - 12K # TJD-12000-RODNUT for your jack (I looked it up on Big Tex's website and it is a 12k Ram jack), but that is the only replacement part currently available. If it ends up needing more than that, you will need a full replacement.
The Square Direct Weld Jack - Drop Leg w/ Spring Return - Sidewind - 28-3/4" Lift - 12K # TJD-15000SP-F you found looks to be an exact replacement for what you currently have installed. It is more expensive to go with a full replacement, but I can honestly say it will be a lot easier than trying to fix an old one.
What do you typically use your Big Tex Trailer for?
Product Page this Question was Asked From
Square Direct Weld Trailer Jack - Drop Leg w/ Spring - Sidewind - 15" Lift - 12,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- 5th Wheel Trailer
- Gooseneck Trailer
- Side-Mount Jacks
- Sidewind Jack
- 10001 lbs or More
- Manual Jack
- 28-3/4 Inch Lift
- Weld-On
- With Rectangle Foot
- etrailer
more information >
Continue Researching
- Shop: Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K
- Shop: Replacement Lifting Nut for Curt Heavy Duty Direct Weld Square Jack
- Search Results: add coupon code
- Search Results: 12000 lb jack
- Shop: Square Direct Weld Trailer Jack - Drop Leg w/ Spring - Sidewind - 12-3/8" Lift - 10,000 lbs
- Shop: Square A-Frame Trailer Jack w/ Footplate - Drop Leg - Sidewind - 15-1/4" Lift - 3,000 lbs
- Search Results: drop leg
- Q&A: How To Re-Assemble The RAM TJD-12000SP Trailer Jack
- Shop: Square A-Frame Trailer Jack w/ Footplate - Drop Leg - Sidewind - 15-1/4" Lift - 3,000 lbs
- Video: Review of etrailer TJD-12000 Series Jack Replacement Rod And Nut - TJD-12000-RODNUT
- Shop: Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear
- Search Results: karavan
- Search Results: lifting nut
- Search Results: gate latch
- Search Results: slide motor
- Shop: etrailer Dual-Pin Two-Speed Square Tube Jack - 13-1/2" Lift - 12,000 lbs
- Q&A: Could etrailer Replacement Rod and Nut TJD-12000-RODNUT Fit 2016 Big Tex
- Q&A: Are Replacement Rod And Nuts Available For A 2001 Circle J Riata Horse Trailer Front Jack
- Q&A: Trailer Jack that Fits BigTex 70Ch-16 Car Hauler
- Video: Review of etrailer Camper Jacks - Trailer Jack - TJD-12000SP-FIP
- Video: Rebuilding a Bulldog 12000-lb Capacity Jack
- Q&A: Replacement Slide Out Motor for a 2006 Winnebago View
- Video: Ultimate Overview of the Square Direct Weld Jack
- Q&A: How to Replace Interior Ram Jack Rod and Nut # TJD-12000-RODNUT on 12000 Series Jacks
- Video: Hands-On with the Square Direct Weld Jack
- Q&A: Replacement Drop Leg 12K Jacks for a 2016 14k PJ Trailer
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
on Camper Jacks
Mike
7/10/2025
The old jack is welded at at least 5 different places on the trailer frame. I would like to buy the complete new jack,leave the old outside of the jack welded to the frame and just use guts of the new jack. Is this possible?