Tap Size to Clean Bolt Holes for etrailer Hitch Installation on 2011 Honda CR-V
Updated 09/12/2025 | Published 05/27/2025
Products Featured in This Question
Question:
What size tap do I need to clean the bolt holes on a 2011 Honda CRV? I see some feedback that a tap is used on rusty holes, but no one mentions the size. Thanks.
asked by: Terry
Expert Reply:
Hey Terry! Before using a tap we do recommend trying to clean out the holes. Typically this is enough to be able to install the bolts and you don't risk messing anything up. I attached an article below which covers that process. The bolts used to install the # e39AR are M10x1.25 so the corresponding tap will do the trick if you go that route.
What do you plan on using the hitch for? If you plan on towing make sure you also get wiring # 118427 along with a ball mount # e77DR for a complete setup. If you need anything else feel free to reply below.
(click to enlarge)
Product Page this Question was Asked From
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: DIY 2012 Honda CR-V Installation for the etrailer Trailer Hitch Receiver
- Video: Installation Guide for the etrailer Trailer Hitch Receiver on a 2010 Honda CR-V
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Trailer Hitch Weight for a 2011 Honda CR-V
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Trailer Wiring Diagrams
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: How to Choose a Trailer Brake Controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Wiring
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: How to Measure for Trailer Hitch Drop
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Video: Installing the Curt Trailer Hitch Receiver on a 2025 Toyota RAV4
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Shop: Brake Controller
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer jack
- Video: Clean Up Your Trailer Wiring
on Trailer Hitch
Robin H.
9/12/2025
Hey Terry, did the M10x1.25 tap work for cleaning the bolt holes on your Honda CRV? I'm curious to know if the process went smoothly, as it could help others facing a similar task.