Metal Valve Stems that Fit Aluminum Eagle Trailer Wheel part # LH36VR

Question

Question:

I have a set of LH36VR wheels. I wanting to switch to metal valve stems. Will the AM20906 work in these wheels? Thanks.

asked by: Shane A

0

Expert Reply:

Hey Shane, yes the replacement metal valve stem part # AM20906 does fit the Aluminum Eagle Trailer Wheel part # LH36VR that you referenced. It comes with fittings to allow it to basically fit all trailer wheel sizes. Did your rubber ones fail?

expert reply by: Jameson C

0

Shane A.

2/4/2025

No they are fine, I want to use a pass through TPMS.

Jameson C.

2/4/2025

@ShaneA Gotcha! What system are you using?

Shane A.

2/4/2025

@JamesonC I have not decided yet. I will need one with a repeater as my camper is 36’.

Jameson C.

2/4/2025

@ShaneA How many tires do you want to monitor? You are wanting ones that attach to the valve stems correct? Like a flow thru design?

See All (5) Replies to Shane A. ∨

Answer 1

Hi Tyrell! The Taskmaster Aluminum County Line Series Trailer Wheel - 15" x 5" - 5 on 4-1/2 - Machined Black Fork #TA27XR does indeed come with the black center cap. If you were also interested in the 15" Lionshead Aluminum Eagle…

view full answer...

Answer 2

The valve stem hole diameter of the wheel and tire part #AM32680 that you referenced is .625 of an inch. For an upgraded valve stem we have the chrome-plated brass part #AM20906 which fits this hole size as well as the smaller size and can handle up…

view full answer...

Answer 3

I would be happy to help you find the correct replacement hub, but unfortunately we do not have a breakdown of the specific components your trailer uses so you will need to confirm your bearing combination. The easiest way to do this is remove the…

view full answer...

Answer 4

The Dexter "8-248" is a hub assembly for 3,500 lb axles that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in both 5 on 4-1/2" and 5 on 4-3/4" bolt patterns therefore you would need to…

view full answer...

Answer 5

A brake axle would have brakes, either electric or hydraulic drum or disc brakes while an idler hub would have no brakes. Many times, a tandem axle trailer will have one braking axle and one idler axle. The 3500 lb capacity #35545I-EZ-89 axle you…

view full answer...

Answer 6

Your Kendon fold-up trailer has a 2K axle, given the 1.063 diameter spindle you referenced. Assuming you have idler hubs, you'd need #8-91-05UC1-EZ for a 4 on 4 bolt pattern or #AKIHUB-545-2-LF-2K for a 5 on 4-1/2 inch bolt pattern. The L44649…

view full answer...

Answer 7

Inserting a drill bit into the valve stem hole on your wheel and matching the drill size to the hole size is a route that a lot of people go, so it's certainly a fine method. If you have a digital caliper handy you could also just go the old…

view full answer...

Answer 8

Dexstar wheels are not typically limited to only being able to handle 50 psi, if there is a limit that low on a wheel it's almost always the valve stem as typically the wheel is the highest rated pressure rated component. For a higher rated valve…

view full answer...

Answer 9

The Timbren Axle-Less Trailer Suspension System with Hubs - 5 on 4-1/2 - Off-Road Tires - 1,200 lbs #A12WS545 is compatible with the Aluminum HWT Series S5 Split Spoke Trailer Wheel - 12" x 4" Rim - 5 on 4-1/2 #AM22319HWT. With these wheels…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Metal Valve Stems that Fit Aluminum Eagle Trailer Wheel part # LH36VR

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching