Replacement Trailer Hub Assembly for Dexter 8-248 Hubs
Updated 05/29/2020 | Published 12/01/2017
Products Featured in This Question
Question:
Looks like I need the 5 on 4-1/2" hub. Next question. Would the hubs work with the bearing buddy?
asked by: Mark D
Expert Reply:
The Dexter "8-248" is a hub assembly for 3,500 lb axles that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in both 5 on 4-1/2" and 5 on 4-3/4" bolt patterns therefore you would need to confirm your bolt pattern in order to choose the correct hub. I have attached a help article to help you find this as well.
I have also attached my recommendations on each hub for you below.
Dexter:
5 on 4-1/2" - part # 84545BX
5 on 4-3/4" - part # 845475UC1
Isaac D.
5/27/2020
how long is stud
Chris R.
5/29/2020
Pat
5/28/2020
I have a Dexter 8-248 hub. Is there a 6 bolt hub that uses same bearings that i can swap to.
Chris R.
5/29/2020
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2
- Trailer Hubs and Drums
- Idler Hub
- Standard
- L68149 / L44649
- Standard Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: hitch pin and clip
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2
- Search Results: equalizer
- Search Results: bullet proof hitch
- Search Results: adjustable ball mount
- Search Results: 8~248
- Search Results: roof vent
- Search Results: axel
- Q&A: What Information Do You Need to Order a Correct Replacement Axle?
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-3/4 - Pre-Greased
- Shop: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Shop: 2-5/16" Hitch Ball x 1" Diameter Shank - Black Nickel - 7.5K - Trailer Hitch Ball
- Video: Review of the Dexter Trailer Idler Hub Assembly for 3,500-lb Axles
- Video: Measuring To Choose The Right Trailer Axle
- Video: Review of the EZ Connector Magnetic 7-Way Trailer Connector with Watertight Seal
- Q&A: How to Choose Replacement Axle for Lowe's 5x8 Trailer
- Q&A: Do You Have a Trailer Axle Rated for 3,500 Pounds, 82 1/2" Hub Face and 75" Spring Center?
- Video: The Low-Down on the Trailer Axle with Idler Hubs
- Q&A: 2022 Ford F-250 OEM or Aftermarket Puck System for 5th Wheel Towing
- Q&A: Are All Ford Factory Puck System Dimensions the Same
- Video: Review of etrailer Trailer Jack - Manual Sidewind A Frame Jack Drill Adapter - e88GV
- Video: The Power Behind Stillwell Hydraulic Jacks: Manufacturer Interview
- Video: Review of Stillwell Trailer Jack - Hydraulic Trailer Jack with Connection Kit - ST87VR
- Q&A: Replacing The Zerk Fitting On A Dexter EZ-Lube Trailer Axle
- Q&A: What is Meant by Triple Lip Seal of Dexter Grease Seal # DX49CR
on Trailer Hubs and Drums
Mark
12/1/2017
Looks like I need the 5 on 4-1/2" hub. Next question. Would the hubs work with the bearing buddy?