What Size Mounting Bolts Are Needed For A 2014 Toyota RAV4 Trailer Hitch Receiver

Question

Question:

What size of bolts are in the kit RHK. For use with 2014 Toyota RAV4. Are they self taping?

asked by: Charles H

0

Expert Reply:

Hey Charles,

The bolts lengths vary by 5mm depending on the exact hitch you have but they all use the factory weld nuts so you'd need an M12 x 1.25mm x either 35mm or 40mm bolt. Since they use the factory weld nuts they aren't self tapping, but you'll definitely want to give the weld nuts a good cleaning with a brush # 814092 and some penetrating oil to clean out any rust or debris build up. If you can tell me what brand your hitch is and/or how many bolt holes it has on one side (4 or 6) I can narrow down which part number to use when ordering replacements under # RHK.

expert reply by: Kevin C

0

Robin H.

11/17/2025

Hey Charles, did you get a chance to check which hitch you have on your RAV4 so we can confirm the right bolt length for the kit? Once you have that info, I can help you make sure the replacement hardware matches up.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Hey Jerit, congrats on the new car. We've got a couple of hitches that fit the 2026 Subaru Crosstrek Wilderness. The etrailer Trailer Hitch item #e98912 is going to be the most affordable option. This custom fit class III hitch has a 2"…

view full answer...

Answer 11

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 12

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

What Size Mounting Bolts Are Needed For A 2014 Toyota RAV4 Trailer Hitch Receiver

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching