Is The Deka 16-Gauge Bonded 3 Wire # 16-3B-1 100% Copper Primary Wire

Question

Question:

Is the Deka 16-3B-1 wire 100 copper primary wire??

asked by: Larry

0

Expert Reply:

Hey Larry,

The 16-Gauge Bonded 3 Wire # 16-3B-1 is 100% stranded copper and primary-grade insulated.

expert reply by: Kevin C

0

Jesse M.

11/17/2025

Hey Larry, how did the 16-gauge bonded 3-wire work out for your setup? Knowing how it performed could help others looking for a reliable copper primary wire.

Answer 1

The Hopkins part #HM48235 has 16 gauge for wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 5

Thanks for the information Brian! To add a front hitch to your 2026 Ram 2500 with a diesel engine, you'll need the EcoHitch Hidden Front Hitch item #EH37FR. For camper tie downs front and rear, I recommend the TorkLift Tie Downs item #TL73NR. The…

view full answer...

Answer 6

Hey Randy, good question. Yes, the TowSmart #TS85SR is 100% copper wire, not copper-clad aluminum. That’s a big deal for trailer wiring because copper carries current better, holds up to vibration, and resists corrosion a lot better over time. You’ll…

view full answer...

Answer 7

Hey Al, Since your Dexter #9919860 is a 3,500lb axle you'll need grease seals #RG06-050 which come as a pair. I'd get 3 pairs (6 seals) that way you have an extra incase one goes in funky and bends (I've repacked hundreds of hubs and it…

view full answer...

Answer 8

Hey Mark! All three of these etrailer jacks - the #e72QV 3,500 lb, the #e22QV 3,500 lb with SnapPad, and the #e82QV 5,000 lb with SnapPad - are powered directly through your truck’s 7-way plug. So with your Silverado’s factory 7-way, you can simply…

view full answer...

Answer 9

If the outside of the mounting tabs for a baby moon cover on your wheel measures 10-1/4 inches then the Baby Moon Cover part #AM981306 will fit and work well. These have an inner diameter of 10-1/4 inches. Normally these will only fit 6 lub wheels so…

view full answer...

Answer 10

We have one potential option for your 15 inch wheels, though they do have an inside diameter of 10-1/4 inches, which is close enough to 10-3/8 inches that I did want to at least mention it in case you just want to verify your measurement. The option…

view full answer...

Answer 11

We have ecerything you need! For the LM67048 Bearing, you'll need: -The Replacement Trailer Hub Bearing #LM67048, For the 25580 Bearing, you'll need: -The Replacement Trailer Hub Bearing #25580, For the LM67010 Race, you'll need: -The…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Is The Deka 16-Gauge Bonded 3 Wire # 16-3B-1 100% Copper Primary Wire

Product Page this Question was Asked From

Continue Researching