Replacement Trailer Taillight Lens for Grote 9015

Question

Question:

Need replacement amber cover for clearance lite Freightliner part Grote 9015

asked by: Faye S

0

Expert Reply:

Hey Faye, after I did some research, it looks like Grote 9015 corresponds to # MC68AB and the replacement lens for it is # A68AB.

expert reply by: Jameson C

0

Jameson C.

12/15/2025

Hey Faye, how did the replacement amber lens work out for your clearance light? Knowing if it fit well could help others looking for the same Freightliner part.

Answer 1

I recommend going with the Thin Line LED Trailer Light, #MCL65AB for amber lights and #MCL65RB for red lights. These sealed, dual-bulb lights can be used as a clearance or side marker lights. I have included a link to a video review and installation…

view full answer...

Answer 2

We do have the white Replacement Exterior Half-Moon Trailer Vent for 3" Diameter Hole #WHMAV2 which is the white version of the #HMAV2 that you referenced and also is what you sent in a picture of so it would work well for you.

view full answer...

Answer 3

The Optronics Clearance or Side Marker Trailer Light #MC68AB and #MC68AB are the same size as the Grote 9015 lights. Unfortunately they are not available from the manufacturer with a LED light. You can change the incandescent bulb to an LED Bulb…

view full answer...

Answer 4

After I did some research, it looks like Grote 9015 corresponds to #MC68AB and the replacement lens for it is #A68AB. The light itself including the housing measures 3-1/2 inches side to side, 1-1/8 inches top to bottom and sticks out 1 inch. Compare…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Trailer Taillight Lens for Grote 9015

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching