Trailer Hitch and Wiring for 2022 Ford F-150 Without Factory Tow Package
Updated 11/21/2024 | Published 11/02/2024
Products Featured in This Question
Question:
I have a 2022 f150 XLT 4x4 with no towing package. I want to install a class V receiver and a 7 pin harness. I cannot find any wiring products that fit. Im not sure if there is a difference in the vehicle side plugs between the newer generation and last gen f150s . What do you recommend?
asked by: Alexander
Expert Reply:
Hi Alexander; assuming you have the factory step bumper you can use the Draw-Tite Ultra Frame Trailer Hitch Receiver # DT35MR you were looking at. For the wiring, I would check to see if you have the factory wiring harness plugged into the back of the dummy plug on your bumper. If you do you can pull the dummy plug and add the # HM40975. If it doesn't work as is, you may have to run it by the dealer to activate the tow package circuits.
If you do not have any factory wiring we will have to go the universal route which starts by adding a 4-way. If you have LED tail lights you need the # C63NR and if you have incandescent tail lights # C75WR (will not work on models with backup sensors). Once the 4-way is installed you can upgrade to a 7-way using the # ETBC7.
Product Page this Question was Asked From
Draw-Tite Ultra Frame Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Trailer Hitch
- For Towing
- Class V
- 1100 lbs TW
- 11000 lbs GTW
- 14000 lbs WD GTW
- 2 Inch Hitch
- 1400 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Ultra Frame Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Trailer Wiring
- Video: DIY Install: Draw-Tite Ultra Frame Trailer Hitch Receiver on your 2023 Ford F-150
- Search Results: brake controller
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Q&A: Will Draw-Tite Hitch Fit on a 2018 Ford F-150 with a Factory Hitch
- Shop: Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: hitch lock
- Search Results: towing accessories
- Search Results: trailer hitch ball mount
- Video: DIY 2018 Ford F-150 Installation for the Curt Trailer Hitch Receiver
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - Up to 2 Axles - Proportional
- Shop: Towsmart Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Recommended Hitch, Wiring Harness, and Brake Controller for a 2020 Ford F-150
- Q&A: Can a Weight Distribution System be Used on an I Beam Trailer
- Video: Install: Draw-Tite Ultra Frame Trailer Hitch Receiver on a 2016 Ford F-150
- Video: Draw-Tite Ultra Frame Trailer Hitch Installation Guide - 2018 Ford F-150
- Shop: Mud Flaps
- Shop: Side Window Vents
- Shop: Trim Kits
- Shop: Replacement OEM Wiring Harness for Ford F-150
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Search Results: trailer wiring
- Video: Set up: Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector on a 2018 Ford F-150
- Search Results: tonneau cover
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Search Results: trailer brake controller
on Trailer Hitch
Alexander
11/20/2024
Thank you for the reply. I have stock 4 pin wiring in place and #ETBC7 is ordered. Once I install this 7 pin wiring, what route do I take to install a brake controller? Will a vehicle specific plug work or does it need to be wired into the universal 7 pin wiring?