Can Two Self-Contained Hydraulic Jacks Be Used Together On Construction Trailer

Question

Question:

Can the Self-Contained Hydraulic Jack be combined with another to make it a 2 jack system for my construction trailer?

asked by: Matt

0

Expert Reply:

Hi Mike; you can install two of the Self-Contained Hydraulic Jack # e33VV on your construction trailer. However, they will run as two separate units with different controllers. If you want a system that has two hydraulic jacks that work together we have the Dexter Dual Hydraulic Jack System w/ Double Acting Pump # DX42CR.

expert reply by: Robin H

0

Robin H.

12/15/2025

Hey Mike, how did things turn out with the hydraulic jack setup on your construction trailer? Did you end up going with two self-contained jacks or the Dexter dual system? Your update could make it easier for the next person working on a similar trailer.

Answer 1

Hey Michael. As of right now we do not have a hydraulic jack that can tie into your hydraulic system (Though there have been talks around the building of this possibility), nor the add on to convert a manual to hydraulic, but we do have the #e33VV…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Can Two Self-Contained Hydraulic Jacks Be Used Together On Construction Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching