Availability of Replacement Lens for LED Porch Light # DG52726VP

Question

Question:

On the porch light DG52726VP, I only need the dark amber cover. I dont need the full assembly. Can I buy just the lens cover?

asked by: Neal B

0

Expert Reply:

Hey Neal, yes we have just the amber lens of the part # DG52726VP with the part # VAL47CR.

expert reply by: Jameson C

0

Jameson C.

1/5/2026

Hey Neal, did the replacement amber lens work out for your porch light? Knowing how it fit could help others looking for the same part.

Answer 1

On the ends of the Brophy tie downs #HSAB where you would tie off the camper the tip is turn up to be parallel with the ground. The angled design allows more clearance between hold-downs and truck fenders.On #HSSF the tips are not turn up and are at…

view full answer...

Answer 2

Based on the dimensions you mentioned the Replacement Lens for Diamond LED Porch Light #VAL47CR would be correct. This is a standard size for RV porch light replacement lenses so it would be what you are looking for.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Availability of Replacement Lens for LED Porch Light # DG52726VP

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching