Is There a Gear Replacement For Lippert Quick Drop Tongue Jack

Question

Question:

Are parts available for the drill powered Lipert trailer jack? The gear assembly is worn out, where the handle connects to. Are these parts available?

asked by: Roger H

0

Expert Reply:

Hi Roger,

I checked with Lippert, and sadly a gear is not an available replacement part for the Lippert Quick Drop Tongue Jack # LC733926.

The only replaceable parts are the mounting hardware and footpad so the best I can offer is to replace it with a new one.

expert reply by: Kyle S

0

Robin H.

1/12/2026

Hey Roger, were you able to replace your Lippert Quick Drop jack after finding out the gear assembly isn’t available separately? Knowing what route you took could help others facing the same worn gear issue.

Roger H.

1/12/2026

@RobinH I had to buy a new jack. No parts available.

Answer 1

Hi Mark; the only jack like that is the Lippert Power Stance Electric Trailer Jack #LC89VR but it exceeds the amount you're looking to spend. If you're fine with one that only runs off of the 7-way then I recommend the etrailer Electric…

view full answer...

Answer 2

The Dutton-Lainson A-Frame Trailer Jack #DL22530 is currently our only manual A-Frame tongue jack with a 2" outer tube. The Lippert Quick Drop Tongue Jack #LC733926 that supersedes your 423192 jack along with our other jacks have all gone to the…

view full answer...

Answer 3

Hi Todd, I do have a drill-powered A-frame jack for your enclosed trailer that meets all of your needs, and what I recommend for you is the Lippert Quick Drop Tongue Jack #LC733926. The #LC733926 just requires a 3/4" socket which you can use…

view full answer...

Answer 4

Hey John; your standard cordless drill will have no issues operating the Lippert Quick Drop Tongue Jack #LC733926. Just make sure your battery is charged or it might not perform as well as you want it to. The jack has a lift capacity of 1,500 lbs so…

view full answer...

Answer 5

In either position the handle of the Lippert Quick Drop Tongue Jack #LC733926 would not spin and lower on it's own. There's enough friction in the screw of the jack to prevent vibration from causing it to turn on it's own.

view full answer...

Answer 6

You can see all of our available jack caster wheel assemblies on the linked page. These fit on a 2-inch-diameter jack tube, such as #BD500245. If you can find a brand name or part number on your jack that will help to narrow down the correct parts,…

view full answer...

Answer 7

The vast majority of trailer jack wheels don't use traditional steel ball bearings as they aren't really meant for rotation speed but rather weight bearings. I am not aware of any options which use traditional steel ball bearings. The…

view full answer...

Answer 8

The Ram Removable Caster Assembly, #JC-101, is a swiveling caster when attached to the jack. The caster assembly uses a nylon bushing at the swivel point between the connected mounting tube and the wheel assembly.

view full answer...

Answer 9

Gary, I find the Ark Xtreme Off-Road Swivel Trailer Jack #ORJW350D is one of the best jacks for using the wheel to move a trailer around. It has a dual wheel setup which also makes it easier on loose surfaces such as gravel and grass. This jack will…

view full answer...

Answer 10

The 3" bolt hole spacing is the standard pattern for mounting bolt holes on most trailers. The Lippert Quick Drop Tongue Jack #LC733926 that you are looking at will match that same pattern. Do note that the holes on the jack are oblong to…

view full answer...

Answer 11

I tested a few wheels that we have in stock and found that the #JC-102 would physically fit on the Lippert Quick Drop Tongue Jack #LC733926, but would limit your capacity down to wheel's at 1,200lbs.

view full answer...

Answer 12

To add a wheel with the Round A-Frame Trailer Jack #TJA-5000S-B all you need is the wheel caster #JC-101. I would recommend supporting the tongue of the trailer with a floor jack before taking apart anything internal of the jack.

view full answer...

Is There a Gear Replacement For Lippert Quick Drop Tongue Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching