Does etrailer Hitch e89YR Fit 2024 Ford Escape Hybrid

Question

Question:

Does this hitch fit the Hybrid model? Part Number: e89YR

asked by: Danny C

0

Expert Reply:

Hey Danny, yes the etrailer hitch part # e89YR that you referenced does fit your 2024 Ford Escape Hybrid as long as it's not a PHEV model.

expert reply by: Jameson C

0

Jameson C.

1/12/2026

Hey Danny, how did the hitch fit on your Escape Hybrid? Knowing how it worked out could help others checking fit for the same model.

Answer 1

Hi Ken! The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C67MJ will indeed fit your 2025 Ford Escape PHEV. I confirmed this directly with Curt and this hitch is actually specifically for the PHEV and will not fit the other versions…

view full answer...

Answer 2

Hi Bill; I can understand wanting to make sure, and I can tell you the Blue Ox base plate will fit a 2024 Ford Escape Plug-In Hybrid, though no we have not done an install. We have our own team here dedicated specifically to these fits, and I can…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Does etrailer Hitch e89YR Fit 2024 Ford Escape Hybrid

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching