Dimensions And Hole Spacing For The Rhino-Rack Recovery Track Carrier for Pioneer Platform Rack

Question

Question:

The bracket that attaches to the track what are the dimensions and hole spacing?

asked by: Jaime B

0

RR Track Brackets
(click to enlarge)

Expert Reply:

Hi Jaime,

I drew up a little diagram for the Rhino-Rack Recovery Track Carrier for Pioneer Platform Rack # RR43159-RMTXMPS so you can see the dimensions. If you need anything else just let me know.

expert reply by: Kevin C

0

Rhino-Rack Recovery Track Carrier Dimensions
(click to enlarge)

Kate F.

1/27/2026

Hey Jaime, did the diagram for the Rhino-Rack Recovery Track Carrier give you the details you needed on the bracket’s dimensions and hole spacing? Your feedback could help others looking for the same info.

Answer 1

According to Maxtrax, the mounting holes on the #MA24ZV are 10" on center across the width of the board and 25" lengthwise. All of the mounting pins like #MA48PR use M10 bolts so you will need to drill an appropriate hole based on the type…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Dimensions And Hole Spacing For The Rhino-Rack Recovery Track Carrier for Pioneer Platform Rack

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching