Spindle Dimensions For The #42 Spindle # TRU57FR

Question

Question:

Is the colored drawing showing LENGTHS of diameters referenced as R50642 the same dimensions for TRU57FR ? Am trying to design around off the shelf spindle dimensions for a unique application.

asked by: J E

0

R50642
(click to enlarge)

Expert Reply:

Hi J,

The R50642 has slightly different dimensions when it comes to length when compared to the # TRU57FR. I've attached a little diagram below showing the lengths of each journal on the # TRU57FR. If you need anything else just let me know and I'd be happy to help.

expert reply by: Kevin C

0

TRU57FR Length Dimensions
(click to enlarge)

J E.

8/27/2024

Thanks for the info.

Answer 1

Hello James. We have the following parts available for your Dexter Nev-R-Adjust brakes: -Replacement Dexter Adjusting Spring #046-139-00 -Replacement Shoe and Lining for Nev-R-Adjust 12" x 2" Electric - RH #K71-676 -Replacement Shoe and…

view full answer...

Answer 2

Hey Dale, both DeeMax and Hydrastar make really nice disc brake components. Either kit is going to work really well for your 2022 Grand Design Reflection 337RLS. If you want the best of the best and don't mind paying for the premium brand then go…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hey Michael! The Roadmaster Comfort Ride Leaf Spring Suspension Kit #RM82MR will fit your Wildwood X-Lite with underslung axles. We have confirmed this with Roadmaster. Most travel trailers and 5th wheels have overslung axles which is why you…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Spindle Dimensions For The #42 Spindle # TRU57FR

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching