Replacement Lock Cover for Inno Feet

Question

Question:

Dear Etrailer.com: I lost one of my Inno lock covers, including the lock. Is there any way to just purchase one lock cover, with a lock core that is the same as my other lock cores? Moreover, the same numbered lock core so I can use the same key on all 4? Thank you. Scott

asked by: Scott

0

Expert Reply:

Hi Scott; sorry for the delay on this it took a while to hear back from Inno. The part you need is the Replacement Lock Cover Set for Inno Roof Rack Feet Stays for Bare Roofs # IN97YV. This replaces the lock and cover on the # INSUT. However, this will be a random lock so more than likely it won't match the others on your roof rack. We don't have a way to get a specific lock core for it to remain keyed alike.

expert reply by: Robin H

0

Scott W.

6/21/2024

Hi Robin: Thanks for the response. Aside from the Lock Cover (and new random lock number) is it possible to just order 4 locks and replace them in each of the lock covers? Scott

Robin H.

6/23/2024

@ScottW the lock cover set is the only way Inno offers the replacement lock. They don't have the lock cores separately as a replacement part.

Answer 1

Hey there Pavel! We have a possible solution for you to get replacement endcaps and keys on your Inno Square Bar Roof Rack #IN62QR for your Prius. The only way we have to get everything matching is to get Inno Feet for Square Crossbars - Naked Roofs…

view full answer...

Answer 2

There should be a number on the locking core of your Inno Roof Rack. We have a wide array of keys. If the core matches the key number on our site, that is the one you need! Here is a list of all the Inno Keys. T257 #INT257 T282 #INISKT282 T261…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Lock Cover for Inno Feet

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching