Replacement Bearings And Grease Seals For A Load Rite Boat Trailer Model 5S22T4700TG1

Question

Question:

Looking for the right bearing seals for my boat trailer. Original axles from the Load Rite factory. Model 5S22T4700TG1

asked by: Chad H

0

Expert Reply:

Hey Chad,

There unfortunately isn't a guide to tell us the correct bearings and seals for your Load Rite boat trailer so you'll need to remove the hub and check for the part numbers or measure the spindle and hub bore hole. With a caliper # PTW80157 you'll want to measure points B, C, and D on the spindle for the inner diameters and the hub bore hole for the outer diameter. Once we have these measurements I can look up the correct replacements.

expert reply by: Kevin C

0

Spindle Measurement Guide
(click to enlarge)

Answer 1

I apologize for any confusion on what the proper torque specs are for 1/2 inch lug nuts on trailer wheels. I attached a picture of a chart to the right that details what the proper torque specs are for a trailer wheels lugs based on lug size, wheel…

view full answer...

Answer 2

What you'll want to do is refer to your instructions for the proper torque specs. For example, the instructions for the 5.2K - 6K Kodiak Disc Brake Kit #K2HR526D call for the brake mounting flange to be welded to the spindle and then the caliper…

view full answer...

Answer 3

The inner diameter of the Stainless Steel Drive-In Grease Cap w/ Plug #DE69YR measures 1-7/8" (see attached).

view full answer...

Answer 4

Hey Barry, sure do! The seal that comes with the #DX87UR bearing kit is a 1.719" ID and 2.565" OD. We offer this seal individually as part #58846.

view full answer...

Answer 5

There are grease seals with inner diameters of 1.687 inches, #168255TB, or 1.688 inches, #168233, that would be a better fit. If the outer diameters match the inner hub bore diameter then you can use one of them instead. Seal #168255TB has an inner…

view full answer...

Answer 6

Hey Jeff, thanks for the information. It sounds like you need the Double Lip Seal for 3,700-lb Marine Hubs item #168255TB. It fits a inner diameter of 1.687" and an outer diameter of 2.561". What kind of trailer do you have?

view full answer...

Answer 7

We have the Dexter Axle Double Lip Seal for Marine Hubs #168255TB which has the 1.68 inch diameter you need along with the 2.56 inch inside hub diameter you need.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Replacement Bearings And Grease Seals For A Load Rite Boat Trailer Model 5S22T4700TG1

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching