Recommended Replacement Head Assembly for a B&W Companion 5th Wheel

Question

Question:

I need of a BandW head assembly modal RVB3370

asked by: Harry F

0

Expert Reply:

Hey Harry, for your B&W Companion OEM 5th Wheel Trailer Hitch w Slider for Ford Towing Prep Package # BWRVK3370 you are going to need the Replacement Head Assembly for B&W Companion 5th Wheel Trailer Hitches # BWRVC3006.

expert reply by: Bryce D

0

Answer 1

No, you can't. I contacted B&W this morning and was told they do not sell the components of their tow and stow ball mounts separately. While you are most likely correct and they are probably interchangeable, B&W wants you to buy a new…

view full answer...

Answer 2

I believe the bearing kit you will need will be part #BK1-100. However, I was unable to exactly cross reference your seal number. I recommend measuring your spindle to find the inner diameter of the seal you need, as well as measuring your seal to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

view full answer...

Answer 12

Hey Joshua, yes the Kenda Karrier KR35 ST175/80R13 LRD part #KE34TJ would fit in place of what you have now as it's exact same tire size and wheel bolt pattern. This will be a nice upgrade in capacity as well as will look a lot nicer as well. How…

view full answer...

Recommended Replacement Head Assembly for a B&W Companion 5th Wheel

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching