Is There A Snap Ring Jack With A Wheel That Uses a 1/2" Pin For The Mounting Plate?

Question

Question:

I have a EZ loader boat trailer that had a Fulton trailer Jack attached at the factory. That jack went bad on a trip and was replaced with a different jack but only had a flat plate in place of a wheel. I would like to replace the jack with a trailer jack with a wheel but the welded mounting plate was modified to support a pin that is 1/2 in. All the Fulton jacks I see advertised have only a 3/8 in pin. Do you have a boat trailer jack that is held on with a C clip and has a 1/2 in pin?

asked by: John K

0

Expert Reply:

Hello John. After looking thru all of the snap-ring jacks we carry, I am sorry to say that we do not offer anything with a wheel that will also use a 1/2" pin. We do have a jack with a wheel and a snap ring that uses a 3/8" pin, the Fulton # FTJ120W0301. We also have one snap ring jack that does use a 1/2" pin, part # TJB-2001-Z, but as lock would have it, this jack has a welded foot plate instead of a wheel.

I know neither of these options fit your description exactly, but these will be the closest options we can offer.

expert reply by: Jesse M

0

John

4/23/2024

Jesse Thanks for the reply, I did look at the FTJ120W301 video and it looks like it will work as long as I weld the new plate to the trailer tung. I will go ahead and order that jack. Thanks for your help. John Kearns

Jesse M.

4/23/2024

@John Yes! If you weld a new plate to the tongue you can use really any jack regardless of pin size so the Fulton # FTJ120W0301 is a great choice.

Answer 1

Hey Mike! You can use the Fulton Boat Trailer Jack w/ Wheel #FTJ120W0301 on your 1998 Four Winns 180 Horizon. However, you will need to measure to see if this matches the current bracket. See the attached photo with measurements. Worst case you can…

view full answer...

Answer 2

If your original Fulton jack is a snap-ring type swivel jack that uses the same 2.313-inch pilot hole diameter then Fulton 1200-lb jack #FTJ120W0301 should do the trick. You may not even need to bother with welding on the (included) new mounting…

view full answer...

Answer 3

What you have there is a Dutton Lainson jack. There is no longer a direct replacement jack, but you can use the #DL22580 which will be an upgrade. This is a swivel jack with a 1,500 lb capacity and 12" of lift. This has dual wheels for easy…

view full answer...

Answer 4

What we have heard is that the Fulton #FTJ120W0301 uses the same style of mounting bracket as the Shelby jack that you have so it would provide the easiest replacement.

view full answer...

Answer 5

Hey Steve, it sounds like you are looking for the Fulton Boat Trailer Jack part #FXP100W0301 which utilizes the style of swivel bracket that it sounds like you have. The pull pin diameter though is 1/2 inch which is the same size for all of these…

view full answer...

Answer 6

In order to remove a welded-on trailer tongue jack you will need to cut off the old welds to release the mounting bracket. This can be done using an angle grinder. The jack can then be replaced with another welded-on option such as the Fulton Marine…

view full answer...

Answer 7

I believe the jack you are looking for a replacement for is a frame mounted, swivel jack, sidewind, that has a 2,000 lb capacity and a wheel caster. We did have a customer come back and say that the Fulton jack part #FTJ120W0301 will attach just fine…

view full answer...

Answer 8

I do have an option for you but we do not have an exact replacement for the Shelby Jack 5764A. Instead, I recommend taking a look at the Fulton Bolt-Thru Swivel Marine Jack part #FXP10W0301. This jack similar to the Shelby uses a bolt through swivel…

view full answer...

Answer 9

What you've got there looks like some type of proprietary mount that we don't offer. We do however have jacks that would work. I'd recommend having the mount removed and using a weld-on jack like the Fulton #FXP100W0301 and the #P9012-00…

view full answer...

Answer 10

The Fulton Magnum jack used the #P9012-00 weld-on bracket which would be compatible with the bracket included with the 1200 lb Fulton Jack, part #FXP100W0301 or the 1500 lb model, part #F1411300301. If your attachment bolt that attaches the jack to…

view full answer...

Answer 11

Based on the picture you submitted the Fulton Marine Jack part #FXP100W0301 that you referenced would be exactly what you'd need and would bolt right up to the mount you have on the trailer frame.

view full answer...

Answer 12

Thank you for that info, and while we have some options for you to replace your Shelby 5764A trailer jack, there isn't one that is going to fit that bolt pattern. So you have a couple of things you can do, which is either have a new plate welded…

view full answer...

Is There A Snap Ring Jack With A Wheel That Uses a 1/2" Pin For The Mounting Plate?

Products Featured in This Question

Continue Researching