Availability of Trailer Jack to Fit with Flat Weld-On Bracket from Shelby Jack

Question

Question:

I am looking for a boat trailer jack to replace my Shelby jack. It’s a weld on bracket similar to item # FXP100W0301. The difference is that the mounting plate is flat. Do you have something that would fit on this bracket?

asked by: Devon S

0

Expert Reply:

I recently had someone else with this same situation and when I reached out to Fulton my contact said that the Shelby connection just isn't used any more so to replace your jack you can use the Fulton Marine Jack # FXP100W0301 that you referenced, and then have the Mounting Bracket # P9012-00 welded on to complete the install.

expert reply by: Jon G

0

Answer 1

I recommend replacing it with the Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs #FTJ120W0301 which will fit your existing jack mount so it will be an exact replacement, and you will actually have a little…

view full answer...

Answer 2

If the holes on your mount are separated by 3 inches the Fulton trailer jack #FXP100W0301 will fit. If you need a new mount you'd need the #P9012-00. For new hardware for the bracket you'd need the #F0933325S00.

view full answer...

Answer 3

It sounds like you're needing a jack like the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301 which installs on trailers that already have the mount welded on with a single bolt attachment for the jack itself (like what we see with part…

view full answer...

Answer 4

What we have heard from our customers is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784. This would be your best option for a direct replacement.

view full answer...

Answer 5

I do have an option for you but Shelby boat trailer jacks are discontinued and we don't offer any direct bolt-on replacements for them. That said, you can easily remove the old flange by cutting or simply place the new jack beside it and leave…

view full answer...

Answer 6

The Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs #FTJ120W0301 provides similar capacity and does have a Snap ring pilot hole diameter of 2-1/2"that lines up with your Bulldog Jack.

view full answer...

Answer 7

Thanks for the picture of your trailer jack! Based on that all you need is the part #FXP100W0301 which will easily attach to the welded on bracket you have on your trailer frame.

view full answer...

Answer 8

Hey Mike! You can use the Fulton Boat Trailer Jack w/ Wheel #FTJ120W0301 on your 1998 Four Winns 180 Horizon. However, you will need to measure to see if this matches the current bracket. See the attached photo with measurements. Worst case you can…

view full answer...

Answer 9

I believe the jack you are looking for a replacement for is a frame mounted, swivel jack, sidewind, that has a 2,000 lb capacity and a wheel caster. We did have a customer come back and say that the Fulton jack part #FTJ120W0301 will attach just fine…

view full answer...

Answer 10

Hello John. After looking thru all of the snap-ring jacks we carry, I am sorry to say that we do not offer anything with a wheel that will also use a 1/2" pin. We do have a jack with a wheel and a snap ring that uses a 3/8" pin, the Fulton…

view full answer...

Answer 11

Thank you for that info, and while we have some options for you to replace your Shelby 5764A trailer jack, there isn't one that is going to fit that bolt pattern. So you have a couple of things you can do, which is either have a new plate welded…

view full answer...

Answer 12

Based on the picture you submitted the Fulton Marine Jack part #FXP100W0301 that you referenced would be exactly what you'd need and would bolt right up to the mount you have on the trailer frame.

view full answer...

Availability of Trailer Jack to Fit with Flat Weld-On Bracket from Shelby Jack

Featured Help Information

Miscellaneous Media

Continue Researching