Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Moving a trailer by hand doesn’t have to feel like a workout. The Dutton-Lainson boat trailer jack has an 8" diameter x 2" wide spoked wheel that rolls smoothly over pavement or uneven ground. The caster turns a full 360°, so you can pivot and position your trailer exactly where you want it without dragging or lifting. The J-bolt handle and sidewind crank make setup quick, and the swivel-up design clears the way when you’re ready to tow.
Saltwater ramps and coastal air can destroy ordinary jacks, but this one is made for it. The TUFFPLATE finish uses three layers—a zinc base, chromate coating, and sealed top layer—to protect the steel from corrosion. It lasted nearly 500 hours in salt-spray testing, outlasting standard zinc and powder-coat finishes by a wide margin. Even after repeated exposure to water, the jack stays clean and functional instead of rusting solid.

A smooth, controlled lift makes hitching up far easier. This jack delivers 10" of lift and supports up to 1,000 lbs, ideal for small boats, jet skis, or utility trailers. The sidewind handle keeps your knuckles clear of the frame and lets you raise or lower the tongue without awkward angles. When it’s time to move on, just swing the jack up and lock it in place—no need to remove it from the bracket.
Installing the jack doesn’t require cutting or welding. It bolts directly to trailer frames up to 3" wide x 5" tall using the included bracket and hardware. The bracket height measures 15-1/2" when retracted and extends to 25-9/16", giving you a working range suited for coupler heights around 15" to 24". Once mounted, the 10" clearance from the bracket to the top of the jack keeps it tucked out of the way but ready when you need it.
Dutton-Lainson built this swivel jack with heavy-duty steel tubing—2" outer and 1-3/4" inner diameters—for steady support under load. It’s compact, sturdy, and simple, doing exactly what it needs to without fuss. The 2-year limited warranty backs up the build quality, making it a dependable choice for anyone who wants a straightforward, long-lasting trailer jack.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, neighbors. It's Brad here at etrailer, and today we're taking a look at installing the Dutton-Lainson marine trailer tongue jack. Now this is gonna be a great option for replacing an old one. Or if you are fabricating your own trailer, you can also put one of these on there. Now having a side winder jack is really nice because you're able to be on the side here and raise this jack up. Now you have a total of 10 inches of travel which is gonna be great for a boat trailer like this.
And the name of the product is gonna be the marine, and that's because it's zinc coated so it's gonna hold up even when this goes under water. It's not gonna rust out or corrode. It's gonna have a little bit of protection to that. You also have a nice castered wheel here. It's almost a hard plastic almost rubberized feel to it, and it seems really sturdy, but this allows for if you need to move the trailer around, no problem.
I can easily move this here and it feels nice and sturdy. Now when you are ready to hit the road after you hold your trailer out, you can go ahead, raise this up. It actually has a nice little handle here that's great for your fingers to be able to grab on there, and you can easily raise this up. The great thing is you really don't have to raise this all the way up. You can save yourself some cranking by simply pulling our pin, and then locking in place in this position.
In that way, you have plenty of clearance when you're out on the road. Now this is universal. So as long as your trailer fits within the size recommendations of this, you're gonna be able to bolt this on no problem, and those are gonna be three by five. So you can see we have extra stud here to go wider, and we actually have an extra hole on our bracket here. So if you have a trailer that's five inches tall, you can flip that around and you're still gonna be able to bolt this up and get it nice and sturdy on there.
And our wheel here spins 360 degrees on the caster. So that's nice for maneuverability if you have to move it around in your garage. But also you have a two inch wide contact hatch here. So that's gonna be really good. It's not, you know, pressing too hard on anything. It's gonna be nice and planted on the ground. You also have an eight inch tall tire, so that's gonna be able to roll over little pebbles or anything like that that might get in the way normally. Now you're also gonna want to measure your coupler height on your trailer and make sure that it's gonna work. Because with that 10 inches of travel, the maximum height of your coupler that you can use this with is gonna be 25 inches. So just double check yours and make sure that it falls into there. Now, Dutton-Lainson has been around for a long time since the 1800s. And the great part about this is it's made in the USA and the quality is just really solid. It's gonna be a nice, easy, quick installation on your trailer, and we're actually gonna show you how to do that. So let's take a look at that now. So here we have our boat trailer, and the trailer's great but our jack, as you can tell, is sitting at an angle that's not exactly ideal. And when you lower it down, it kinda wants to shift. So I think it's time that we replace this one. So our first step is going to be to remove the old jack. Now, before removing our old jack, we're gonna want to support our trailer. And that way, the coupler doesn't fall down when we're taking this off, and also it's just gonna make it easier. It's not gonna have stress on the hardware. So you can hook it up to your truck. I'm just gonna be using the floor jack here to kinda just raise this up and support it. So get yours nice and steady. We're also gonna wanna make sure that you chock your wheels while doing this. With our old jack removed, we can go ahead and get our new one in place and we're just gonna be putting it in the same spot. But if this is a new jack that you're putting on a trailer, just make sure that you have enough room to be able to rotate this back and out of the way so you don't wanna have this mounted up and then not be able to actually fold this back. So just make sure you have that clearance. So we get this mounted up. We'll take our bracket here and the holes correspond. So we'll get our top one on first, and pretty easy we're just gonna take our bolt, run this through, and have your bracket. You're gonna want the channel facing out so you'll have that flat side against here. And what I'm gonna do is I'm just gonna hand thread my hardware on here so it kinda holds it in place. You'll have a split washer first, and then we'll just follow it up with the nut. If we cinch this up, like I said, we can get the rest of the hardware up nice and easy and not have to balance our jack. So with our two top bolts here holding this in place, we're gonna go ahead and get our bottom one in and these have multiple holes for different widths of trailer. Ours is gonna be using the bottom hole so it's maxed out, but it's also gonna give it a nice tight fit here on our frame. So with a 14 millimeter socket, we're gonna tighten this up and I'm just gonna kinda snug them doing a cross pattern crisscross here. So it evenly lines up. So putting a little bit of pressure on the bolt head here to cinch this in. Do make sure that it stays nice and level and parallel with or perpendicular with the frame. So this can move a little bit. So as you tighten, just kinda hold this in place to where everything's squared up. Now if they do the bolt starts spinning on you, just you can throw a wrench on the back end to hold that bolt head in place. Now there's no torque setting in the instruction manual as far as tightness, but I just made sure to snug it up. And those brackets will start to kinda pull in. You don't wanna over tighten 'cause it can cause it to bend a little bit, but make sure it's snug enough, and that way it's cinched against the frame. So now we can actually raise this up and get our bottle jack outta here. And just like that, we fixed the leaning of our jack that we had previous, and this just feels a lot more secure. The trailers not want to roll away and lean. And that was a look and installation of the Dutton-Lainson marine trailer tongue jack..
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
Ratings & Reviews

Handyandy
9/11/2024
Trailer jack works perfectly. Very pleased.

Jenny N.
12/5/2023
I do have a shorter jack, part # ORJW350D, to offer. It has a higher price tag however the retracted length is 9.50 inches verses 15.50 inches.

Timothy
8/10/2024
Product has worked lya charm! Way superior to the jack that was on the boat wyI purchased it!
Do you have a question about this Trailer Jack?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.









Brooke M.
4/8/2025
I really like the salt resistant coating they come with. Thanks for sharing the photo. Whether you're boating or ashore, these jacks will get the job done!