Availability of Fulton Swivel Jack that Can Fit Weld On Mounting Bracket of Boat Trailer
Updated 05/05/2025 | Published 04/22/2025
Question:
I have an old Fulton jack that I want to replace and wondering if any current models will bolt up to the old bracket. I found the XLT 1500 jack that is similar, but not quite the same. I have a 1-3/4” diameter pivot boss, with a 1/2” bolt holding it on in center. Locking pin is 3/8” diameter. Mounting height is about 12-13” in lowered position. I see you have an adapter bracket I could buy which would probably work but wondering if there’s anything that will work without it. Thanks, Steve
asked by: Steve
Expert Reply:
Hey Steve, it sounds like you are looking for the Fulton Boat Trailer Jack part # FXP100W0301 which utilizes the style of swivel bracket that it sounds like you have. The pull pin diameter though is 1/2 inch which is the same size for all of these types of jacks but figured I would mention that. If you wanted to email me back with a picture of your mount and your old jack that would be helpful as well.
Continue Researching
- Search Results: swivel jack
- Shop: Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1.2K
- Video: All About the Demco 2-Tang Clevis
- Q&A: What Capacity Jack is Needed at Minimum to Support 3,100 lb Boat and Trailer
- Video: Review of the Pull Pin, Easy Swivel Trailer Jack with Foot
- Shop: Demco 2-Tang Clevis - Adjustable Channel Mount - Black Paint - 20,000 lbs
- Shop: Fulton Adapter Kit - Weld-On XP Jack Mount to F2 Swing-Up Trailer Jack for 3" x 4" Frames
- Shop: Trailer Valet JXS Drill Powered Swivel Jack w/ Footplate - 14" Lift - 1,600 lbs
- Shop: Trailer Valet JX Drill Powered Jack - Pipe Mount - 14-1/2" Lift - 1,800 lbs
- Shop: Dutton-Lainson Pull Pin Swivel Trailer Jack w/ Foot - Sidewind - 10" Lift - 2,000 lbs
- Q&A: Replacement Trailer Jack for Viking Legend Pop-Up Camper
- Q&A: Replacement Trailer Jack Recommendation for Boat Trailer with Weld On Mount
- Search Results: trailer jack
- Q&A: Fulton Jack Recommendation for Triton Dual Axle Boat Trailer with Weld On Fulton Jack
- Video: Don't Forget the Brake Lines | Tips from the Manufacturer
- Search Results: accessories and parts
- Search Results: weld on bracket
- Search Results: weld on plate
- Shop: etrailer Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - 1,000 lbs
- Search Results: trailer jack mounting bracket
- Q&A: How to Determine if the Fulton Swivel Marine Jack JXP10W0301 Will Fit a Trailer
- Search Results: fulton jack
- Q&A: Replacement Jack to Bolt Up to Shelby 5784 Mounting Bracket
- Q&A: Options to Replace Shelby 5764A Trailer Jack
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Trailer Jack
Steve
5/4/2025
The one you recommended has an 8” wheel and the current one is 6”. I would be ok with this but not sure I’ll be able to lower the trailer enough as the lowered height is also 2” higher. I found the FXP10W0301 which appears to be the identical jack but with a 6” wheel and 12-3/4” lowered height. Was going to order this one instead but noticed it won’t be available until July.