Replacement Jack Solution for Shelby 5856A that Uses Same Mount

Question

Question:

I have a boat trailer with a damaged weld on Shelby 5856A jack. Shelby is no longer in business. Is there a replacement jack that will mount onto the welded on bracket or will I have to buy a bolt on, or buy another weld-on and have the old bracket removed and replaced with the new?

asked by: John S

0

Expert Reply:

I recommend replacing it with the Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200 lbs # FTJ120W0301 which will fit your existing jack mount so it will be an exact replacement, and you will actually have a little stronger of a jack as this jack has a 1200lb lift capacity compared to your Shelby jack that had a 1000lb capacity. What that means is that it will be a little easier to jack up and down.

expert reply by: Jameson C

0

Answer 1

I recently had someone else with this same situation and when I reached out to Fulton my contact said that the Shelby connection just isn't used any more so to replace your jack you can use the Fulton Marine Jack #FXP100W0301 that you referenced,…

view full answer...

Answer 2

If the holes on your mount are separated by 3 inches the Fulton trailer jack #FXP100W0301 will fit. If you need a new mount you'd need the #P9012-00. For new hardware for the bracket you'd need the #F0933325S00.

view full answer...

Answer 3

It sounds like you're needing a jack like the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301 which installs on trailers that already have the mount welded on with a single bolt attachment for the jack itself (like what we see with part…

view full answer...

Answer 4

Hey Mike! You can use the Fulton Boat Trailer Jack w/ Wheel #FTJ120W0301 on your 1998 Four Winns 180 Horizon. However, you will need to measure to see if this matches the current bracket. See the attached photo with measurements. Worst case you can…

view full answer...

Answer 5

Thanks for the picture of your trailer jack! Based on that all you need is the part #FXP100W0301 which will easily attach to the welded on bracket you have on your trailer frame.

view full answer...

Answer 6

Based on the picture you submitted the Fulton Marine Jack part #FXP100W0301 that you referenced would be exactly what you'd need and would bolt right up to the mount you have on the trailer frame.

view full answer...

Answer 7

Hey Dan. If your jack mount has a 2-1/2" ring on it then the Round Snap Ring Swivel Jack w/ Footplate item #TJB-2002S-B is going to be your best option. This 2,000 lbs capacity jack attaches to the same size bracket that the Fulton item…

view full answer...

Answer 8

What you've got there looks like some type of proprietary mount that we don't offer. We do however have jacks that would work. I'd recommend having the mount removed and using a weld-on jack like the Fulton #FXP100W0301 and the #P9012-00…

view full answer...

Answer 9

I do have an option for you but Shelby boat trailer jacks are discontinued and we don't offer any direct bolt-on replacements for them. That said, you can easily remove the old flange by cutting or simply place the new jack beside it and leave…

view full answer...

Answer 10

The Fulton Magnum jack used the #P9012-00 weld-on bracket which would be compatible with the bracket included with the 1200 lb Fulton Jack, part #FXP100W0301 or the 1500 lb model, part #F1411300301. If your attachment bolt that attaches the jack to…

view full answer...

Answer 11

The Pro Series jack part #PS1400300303 is designed to fit on a 2-1/2 inch diameter pipe and snap ring like you are needing so this would work great.

view full answer...

Answer 12

Hey Steve, it sounds like you are looking for the Fulton Boat Trailer Jack part #FXP100W0301 which utilizes the style of swivel bracket that it sounds like you have. The pull pin diameter though is 1/2 inch which is the same size for all of these…

view full answer...

Replacement Jack Solution for Shelby 5856A that Uses Same Mount

Continue Researching