Recommended Trailer Hitch for a 2024 Toyota RAV4

Question

Question:

Would you send me a link to video showing installation of hitch E-23ZR on a 2024 Toyota Rav4 Hybrid?

asked by: Tim J

0

Expert Reply:

Hey Tim, as of right now we actually do not have any videos shot installing the etrailer Trailer Hitch Receiver # e23ZR on a 2024 Toyota RAV4.

We do have one shot for a 2023 that I've attached for you to check out which should give you a pretty good idea what you're in for.

expert reply by: Bryce D

0

Timothy C.

4/20/2024

Bryce, When we tried to install the hitch on a 2024 Rav4 we found that the threaded holes on the car were on the inside of the car's frame, but the hitch matched the outside of the frame. There is no way to bore new holes in this frame. We could cut the main bar of the hitch but then the angle would be wrong on the flat steel with the holes in it. Tim

Bryce D.

4/22/2024

@TimothyC Ok that's interesting, let me get this over to our fitguide team and let them know. The hitch is supposed to just easily bolt up to your frame but I see the issue.

Tim

4/24/2024

@TimothyC After further inspection there are four bolt holes two on each side of the 2024 Rav4. We will install the hitch correctly tomorrow. I apologize for any inconvenience.

Bryce D.

4/24/2024

@Tim No problem at all Tim, glad you got it sorted out.

Answer 1

The hitch with the best ground clearance that fits your 2024 Toyota RAV4 is the Curt part #C66KR but this is a 1-1/4 inch hitch. Only the hitch opening hangs below the rear bumper which allows for the better ground clearance. If you instead wanted…

view full answer...

Answer 2

The trailer hitch receiver that fits your 2024 Toyota RAV4 and has the best clearances - both bumper clearance and ground clearance - is the EcoHitch, with the correct fit for the '24 RAV4 being the following: - EcoHitch Hidden Trailer Hitch…

view full answer...

Answer 3

Do you have a 2020 Rav4 or a 2021? We don't have hitch fits for the 2021 models at this time.

view full answer...

Answer 4

Hey Robert, thanks for reaching out! The Curt T-Connector Vehicle Wiring Harness #C56434 doesn't short out often enough to have a verified percentage that goes out. This has the newer Curt module so it will still work great. These types of wiring…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Recommended Trailer Hitch for a 2024 Toyota RAV4

Featured Help Information

Miscellaneous Media

Continue Researching