How To Select Between 2 Speeds On Jack # TJD2SP-25100 and Electric Jack Availability

Question

Question:

I watched the video but it does not show how to use the 2 speeds. I have a large enclosed trailer that the dual jacks would be nice for.Also do you sell a single electric jack? Thank you.

asked by: Dan

0

Expert Reply:

To use the 2nd speed on the Square 2-Speed Jack # TJD2SP-25100 you need to remove the handle and attach it to the other shaft on the gear box. This is how you select either the high gear of 1" every 4-1/2 turns or 1" for every 34-1/2 turns.

The Bulldog Powered-Drive Kit # BD1824200100 will allow you to electrically control a similar Bulldog Single Speed Square Jack # BD182815.

expert reply by: Bud M

0

Answer 1

Hello Angela, I can definitely point you in the right direction. Sundowner does not list exactly what kind of jacks they use online, but looking at pictures of these trailers online, the front jack on the Sundowner horse trailer looks very much like…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 5

Hi Dan! I have a couple potentially dumb questions. Are you sure you have a 1.5" hitch receiver? Was that measured at the inside or outside of the hitch opening? And if it is truly 1.5" for the inside of the receiver, what is this hitch on?…

view full answer...

Answer 6

Hey James, thanks for the information. For a compatible grease seal you'll need the Grease Seal item #GS-2125DL. This grease seal has a 2.125" I.D. and 3.376" O.D.. It is sold individually. What color are your brake drums? I found the…

view full answer...

Answer 7

Hey Lionel, thanks for reaching out! You just need the Connecting Rod #LG-XTB to connect the Square 2-Speed Jack #e72ZV and Square Jack Follow Leg #TJD-25100 together. Be sure to pick up the Crank Handle #TJD-12000-HD if you don't already have…

view full answer...

Answer 8

Yes, I contacted a Tech at Dexter Axle for verification and the Dexter Axle UFP Idler Hub, #DA54FR is confirmed to be a replacement for the Reliable Brand, Model BT-150A “short” hub on 2,100 lb. axles. The inner & outer races are included but not…

view full answer...

Answer 9

Welcome back, Ian! With a 3,500 pound Dexter E-Z Lube using the #L68149 inner bearing, you will want the Bearing Buddy Spindle Grease Seal Set #BB60002. This does also include the seal as well as the wear sleeve and will fit your 3,500 pound Dexter…

view full answer...

Answer 10

Hey Brent! I've got a couple of options for you. The only jack we have with that capacity that is going to be that short is the Bulldog Square Jack w/ Footplate item #BD96FR. It's 19-15/16" when retracted, however it can not be connected…

view full answer...

Answer 11

Hello Tim, On the Square Jack Follow Leg - Side Pin Drop Leg - Spring Return - 25K Lift - 24-1/2" Travel #TJD-25100 from the bottom of the foot to the bottom of the outer tube is 5" retracted and 18" extended. I attached an image as…

view full answer...

How To Select Between 2 Speeds On Jack # TJD2SP-25100 and Electric Jack Availability

Product Page this Question was Asked From

Continue Researching