Wiring Adapters to Install a Redarc Tow-Pro Liberty in a 2021 Subaru Ascent w/ the Tow Package

Question

Question:

I have a 2023 Subaru Ascent Touring Edition with Factory OEM Tow package. Id like to install the Redarc Liberty controller via the factory plug thats bundled in the left foot well area. I dont want to do any splicing, so I would like a list of all the wiring adapters to achieve that .. I believe I need a Tekonsha Subara harness and a RedArc to Tekonsha Harness. Thanks for your help,

asked by: Robert E

0

Expert Reply:

To install a Redarc Tow-Pro Liberty Brake Controller item # RED24FR in your 2023 Subaru Ascent without cutting wires you will need the following adapters:

Redarc Tow-Pro Wiring Adapter for Tekonsha Brake Controller Harness item # 331-TPH-017

Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dual Plug In item # 3062-P

expert reply by: Jerred H

0

Answer 1

Yes, there is a plug-and-play harness for installing the Redarc Tow-Pro Elite Brake Controller #RED63RR in your 2023 Subaru Ascent with tow package. You just need the Tekonsha Plug-In Wiring Adapter #3062-P. This adapter connects to the wiring…

view full answer...

Answer 2

Yes, Tekonsha released the part #3062-P which is a brake controller install harness that fits your 2019 Subaru Ascent and would work well. I attached a picture that shows where you'll find it on your vehicle too. For a brake controller I would…

view full answer...

Answer 3

The Redarc Tow-Pro Elite Trailer Brake Controller #RED44FR you were looking at will absolutely work in your 2021 Subaru Ascent, but how it is installed will depend on if your Ascent has the factory tow package or not. If your Ascent has the factory…

view full answer...

Answer 4

If your 2022 Subaru Ascent has the factory tow package with the factory installed 7-way trailer connector, it will have the factory brake controller connector located above the driver's side kick panel forward of the hood latch as shown in the…

view full answer...

Answer 5

Yes, it can. To add a 7-Way to your 2021 Subaru Ascent you will need the Tekonsha OEM Replacement Vehicle Wiring Harness item #118290. This will provide you a 7-way connector and all the wiring and hardware you will need to install it and connect the…

view full answer...

Answer 6

Yes, you will need a brake controller. To add one to your 2019 Subaru Ascent, I recommend the Redarc Tow-Pro Liberty Brake Controller item #RED24FR. This is a proportional brake controller that activates your trailer's brakes when your Subaru…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Wiring Adapters to Install a Redarc Tow-Pro Liberty in a 2021 Subaru Ascent w/ the Tow Package

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching