Replacement Hub and Drum Assembly for Tru-Ryde RVD-H-545

Question

Question:

What would be the exact replacement hub/drum assembly for an RVD-H-545 SZ12. It fits a 2016 Forest River Surveyor 245bhs. The outer bearing seized and I will need to replace the assembly.

asked by: Jason M

1

Helpful Expert Reply:

To replace your Tru-Ryde RVD-H-545 hub and drum assembly you need the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles # AKHD-545-35-EZ-K. This isn't the exact same brand but all of the bearings and seals match so it will be a direct replacement for what you have.

expert reply by: Jon G

1

Tru-Ryde Trailer Hub and Drum RVD-H-545
(click to enlarge)

Answer 1

The Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part #AKFBBRK-35.

view full answer...

Answer 2

For your application you need the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles #AKHD-545-35-EZ-K to replace the Tru-Ryde RVD-H-545 trailer hub/drum assembly. This is designed for the industry standard #84 spindle so it uses inner bearing…

view full answer...

Answer 3

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 4

Hey Rob, The Hydraulic Trailer Brake Kit - Uni-Servo - 10" - Left and Right Hand Assemblies #AKUBRK-35 you were looking at would be a single pair (left/right). These are also available with a free-backing feature and Dacromet finish with part…

view full answer...

Answer 5

We have found in the past that the TruRyde RVD-H-545 uses 1/2" diameter x 2" long wheel studs. For a replacement you can use the #7-122.

view full answer...

Answer 6

If you have a 3500 lb axle, you'll have a 5 on 4-1/2 inch bolt pattern. You can confirm this by measuring the center to center distance between 2 adjacent wheel studs. If it's 2-5/8 of an inch, you absolutely for certain have a 5 on 4-1/2…

view full answer...

Answer 7

Hello Rodney, thanks for reaching out. The Easy Grease Trailer Hub and Drum Assembly #AKHD-545-35-EZ-K uses a lithium complex grease. This is compatible with a few different greases, but what I recommend is the LubriMatic LMX Industrial Strength…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Hub and Drum Assembly for Tru-Ryde RVD-H-545

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching