10" Hydraulic Surge Brake Assemblies Needed For A Boat Trailer

Question

Question:

Need 1 pair hydro surge brake. 13 inch wheel 10 inch brake. All I see is 10 pair or 25 or 50 I need 1 pair thanks Rob

asked by: Rob R

0

Expert Reply:

Hey Rob,

The Hydraulic Trailer Brake Kit - Uni-Servo - 10" - Left and Right Hand Assemblies # AKUBRK-35 you were looking at would be a single pair (left/right). These are also available with a free-backing feature and Dacromet finish with part # AKFBBRK-35-D for superior corrosion resistance.

expert reply by: Kevin C

0

Answer 1

Hey Dustin, thanks for reaching out! The only surefire way to know if your brakes are free backing or not is to hook your trailer up to your vehicle and back up. If your trailer tires lock up then you have standard hydraulic brakes and need the kit…

view full answer...

Answer 2

The Trailer Hub and Drum Assembly part #AKHD-545-35-EZ-K would be an excellent replacement for a Tru-Ryde Hub/Drum RVD-H-545. Then for new brakes, I recommend the Hydraulic Trailer Brake Kit part #AKFBBRK-35.

view full answer...

Answer 3

To replace your Tru-Ryde RVD-H-545 hub and drum assembly you need the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles #AKHD-545-35-EZ-K. This isn't the exact same brand but all of the bearings and seals match so it will be a direct…

view full answer...

Answer 4

We do have what you need to replace the UFP HD-1377-10 hub and drum as well as add hydraulic brakes for your boat trailer. Here are the exact parts you will need: - Dexter Trailer Hub and Drum Assembly #84546UC3 - Hydraulic Trailer Brake Kit -…

view full answer...

Answer 5

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 6

We have found in the past that the TruRyde RVD-H-545 uses 1/2" diameter x 2" long wheel studs. For a replacement you can use the #7-122.

view full answer...

Answer 7

For your application you need the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles #AKHD-545-35-EZ-K to replace the Tru-Ryde RVD-H-545 trailer hub/drum assembly. This is designed for the industry standard #84 spindle so it uses inner bearing…

view full answer...

Answer 8

Hello Rodney, thanks for reaching out. The Easy Grease Trailer Hub and Drum Assembly #AKHD-545-35-EZ-K uses a lithium complex grease. This is compatible with a few different greases, but what I recommend is the LubriMatic LMX Industrial Strength…

view full answer...

Answer 9

If you have a 3500 lb axle, you'll have a 5 on 4-1/2 inch bolt pattern. You can confirm this by measuring the center to center distance between 2 adjacent wheel studs. If it's 2-5/8 of an inch, you absolutely for certain have a 5 on 4-1/2…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

10" Hydraulic Surge Brake Assemblies Needed For A Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching