Replacing Spindles On A 1994 FLOE PRO-100 Snowmobile Trailer
Updated 09/11/2023 | Published 09/09/2023 >
Products Featured in This Question
Question:
Looking for a replacement spindle for a 1994 FLOE Pro-100 plus 10 foot 2 place snowmobile trailer. 1880 axle. What one should i get? Thanks
asked by: John B
Expert Reply:
We can certainly point you in the right direction. Unfortunately we do not have literature that will give us spindle/bearing sizes based off a year, make and model of trailer. So it may be difficult to recommend a direct replacement without a bit more information.
That said, looking at these 1994 FLOE Pro-100 plus snowmobile trailers, it appears to have a light duty single axle setup. My guess would be something like a 3,500 lb axle, or smaller. The best thing would be to have you confirm the spindle size and/or bearing sizes.
We offer spindles in a variety of sizes. We do recommend replacing both the spindles, and hubs while you are at it. For a 3,500 lb spindle we have the # TRU77FR. You can pair this with the idler hubs # AKIHUB-545-35-EZ-K if you want to go all new. Or for a 2,000 lb axle we have the spindle # TRU94FR and hub # AKIHUB-440-2-1K. If you are going to be replacing the spindles only, it is best to have this done professionally. We could look at replacing the axle entirely. We just need to know what length and weight capacity of axle is needed. Axles are measured across from hub face to hub face.
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Trailer Hubs and Drums
- Idler Hub
- Standard
- L44643 / L44643
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- Redline
more information >
Continue Researching
- Search Results: ring
- Search Results: tire strap
- Search Results: tie down
- Search Results: trailer tires and wheels
- Shop: Caliber TrailBlazer ATV/UTV Tie-Down Kit - 4 Straps - Fits 25" to 35" Tires - 3,300 lbs
- Shop: Kenda 215/60-8 Bias Trailer Tire with 8" Galvanized Wheel - 5 on 4-1/2 - Load Range D
- Q&A: What is Height Difference Between 10 Degree Down and 45 Degree Down Torsion Axle
- Shop: Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 72" Long - 2,200 lbs
- Video: Trailer Idler Hub Assembly for 2,000-lb Axles Spec Review
- Shop: Karrier ST175/80R13 Radial Trailer Tire with 13" Galvanized Wheel - 5 on 4-1/2 - Load Range D
- Q&A: Replacement Hubs for 1997 FLOE Pro 100 Plus Snowmobile Trailer
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 5 on 4-1/2 - Galvanized
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Shop: Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Q&A: Does the Dexter Trailer Hub and Drum Assembly # 84546UC3 Come Fully Assembled
- Q&A: Should There Be a Washer on Trailer Spindle Between Spindle Nut and Outer Bearing
- Q&A: Recommended Replacement for Dexter 8-259 Idler Hub
- Search Results: jack stand
- Search Results: winch stand
- Search Results: lock dust cover
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Shop: Suspension Enhancement
- Shop: Brake Controller

