What Grease Seal Fits the 3,500LB Dexter Axles Under 2022 Grand Design Imagine 2500L Travel Trailer?

Question

Question:

What wheel/grease seals do I need for our 2022 GD 2500RL.

asked by: J G

0

Expert Reply:

According to the information I could find on your 2022 Grand Design 2500RL it comes with 3,500LB Dexter axles. This will use the Grease Seals # RG06-050 for one axle. We also have the Bearing Kit # BK2-100 which includes the bearings, races, and grease seal for one hub.

expert reply by: Bud M

0

Answer 1

Hello Corey. The 3,500 lb axles on your 2018 Grand Design Imagine 2500RL use the standard 3.5K bearing sizes. Meaning you have a #L68149 (1.378" inner diameter) inner bearing, a #L44649 (1.063" inner diameter) outer bearing. The inner race…

view full answer...

Answer 2

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 3

For replacement bearings, races, and seals for your 3,500 lb Lippert axle you can use the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles #BK2-100. This comes with everything you need along with a tang washer and cotter pin.

view full answer...

Answer 4

There are going to be 2 ways to find out what size spindle is on your Dexter 3500lb axles under your car trailer. First every Dexter axle manufactured after April 2001 will have a serial number stamped on the rear of the axle tube near the passenger…

view full answer...

Answer 5

Hey Gaetano, the correct replacement grease seal for a Dexter 3,500 lb trailer axle is the part #58846.

view full answer...

Answer 6

I was able to look up your previous order and find that your Dexter Axle came with the Inner bearing #L68149 and outer bearing #L44649. A great replacement kit for these bearing numbers is the #BK2-100, it will include the inner and outer bearing and…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

What Grease Seal Fits the 3,500LB Dexter Axles Under 2022 Grand Design Imagine 2500L Travel Trailer?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching