What is the Spacing From the Top of the Flat, End Bracket to the Center of the Bolt Hole

Question

Question:

On the Stromberg Carlson 300 accessory hitch. On the flat bracket what is the measurement from the top of the bracket the edge to the center of the screw hole? TIA

asked by: Laura C

1

Helpful Expert Reply:

The spacing from the top of the flat end bracket to the center of the hole on the Stromberg Carlson Adjustable Accessory Hitch Receiver # SC45MR (CC-300) is 1.5".

expert reply by: Scott S

1

Stromberg Carlson Adjustable Hitch Flat End Plate Hole Spacing
(click to enlarge)

Answer 1

Hey Kelly. The Lippert 2" Accessory Receiver Hitch for Up to 66" RV Frames item #LC78DX does not come with installation hardware. I checked with Lippert and they said that this hitch is intended for use with RVs that are prepped for a…

view full answer...

Answer 2

Hey Mike, thanks for reaching out. I see you already got an adjustable hitch on order but I still wanted to reply to your question. The wording on the part page for the Lippert 2" Accessory Receiver Hitch #LC78DX is really weird. This hitch is…

view full answer...

Answer 3

Thanks for reaching out, Alan. I completely understand having a bit of confusion when it comes to our hitch options—we have quite a few. After looking at what’s available for your Outback, there are two different styles to choose from based on how…

view full answer...

Answer 4

Hello Rene, thanks for reaching out. We do have a universal frame mounted hitch that may work on your 2015 Cougar 33RBK 5th Wheel. Take a look at the following: Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide #13703 This…

view full answer...

Answer 5

The ideal RV hitch for your application is the Curt Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide #13703. This is designed for I-beam trailers and will give you the 3 inch drop you are seeking. I've attached a video…

view full answer...

Answer 6

Yes, if you plan on bolting the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR on then you would need to drill holes in the adjustable arms in order to set them to the correct length. There aren't any predrilled so that this one…

view full answer...

Answer 7

Thanks for the pictures. The Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 you mention would be a great option for you since your trailer frame falls within the adjustable range and it has the beefed up tongue weight…

view full answer...

Answer 8

You'd need to box the I-beam frame where you plan to install the Ultra-Fab 2" Trailer Hitch Receiver #UF35-946403 and then you can weld it in place. You'd need to weld around the L-bracket basically of the hitch to the frame. See…

view full answer...

Answer 9

From the crosstube to the face of the receiver is 5-1/4" for the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403. I've attached a dimensional photo for you to reference as well.

view full answer...

Answer 10

The best and easiest option to install a trailer hitch on the back of a trailer is with the Curt RV Bumper Hitch part #C19101 which bolts onto a standard 4" x 4" rear bumper. The Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames…

view full answer...

Answer 11

Appreciate the photos, and we do have a hitch for you, but the Curt #13703 is for a max 72 inch wide frame measured outside to outside of the frame, and it looks like yours is 73 inches. So what you will need instead is a weld-on hitch that is…

view full answer...

Answer 12

The arms of the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 can be taken out and rotated so the welding bracket is on the backside. The receiver tube is 2-1/2 inches square and the arm with the brackets is 2 inches square…

view full answer...

What is the Spacing From the Top of the Flat, End Bracket to the Center of the Bolt Hole

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching