Can Arms of Ultra-Fab Hitch be Rotated

Question

Question:

# UF35-946403. Can the adjustable arms be rotated and inserted so the welding bracket is on the backside?

asked by: Doug B

0

Expert Reply:

The arms of the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames # UF35-946403 can be taken out and rotated so the welding bracket is on the backside. The receiver tube is 2-1/2 inches square and the arm with the brackets is 2 inches square so you can easily remove them and rotate them to the direction of your liking.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The best and easiest option to install a trailer hitch on the back of a trailer is with the Curt RV Bumper Hitch part #C19101 which bolts onto a standard 4" x 4" rear bumper. The Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames…

view full answer...

Answer 2

From the crosstube to the face of the receiver is 5-1/4" for the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403. I've attached a dimensional photo for you to reference as well.

view full answer...

Answer 3

Thanks for the pictures. The Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 you mention would be a great option for you since your trailer frame falls within the adjustable range and it has the beefed up tongue weight…

view full answer...

Answer 4

Appreciate the photos, and we do have a hitch for you, but the Curt #13703 is for a max 72 inch wide frame measured outside to outside of the frame, and it looks like yours is 73 inches. So what you will need instead is a weld-on hitch that is…

view full answer...

Answer 5

You'd need to box the I-beam frame where you plan to install the Ultra-Fab 2" Trailer Hitch Receiver #UF35-946403 and then you can weld it in place. You'd need to weld around the L-bracket basically of the hitch to the frame. See…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 10

Hey Matt, Furrion typically has 4 wires running to their thermostats and the Chill Cube Thermostat #LC74DX is no exception. The harness you see with the thermostat would plug into the Chill Cube's controller and has 4 wires to extra wire to to…

view full answer...

Answer 11

Hey Doug, That's a good question because fit is really important so the cover stays snug on your trailer, and there is a specific way to measure for the etrailer covers. It's pretty simple, and what you want to do is measure the body of the…

view full answer...

Answer 12

Hey Jim! Unfortunately, your experience is pretty common with RV covers. Constant UV exposure is hard on any cover, and most don't significantly outlast their warranty period. The Classic Accessories PolyPro III #052963793635 uses a triple-ply…

view full answer...

Can Arms of Ultra-Fab Hitch be Rotated

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching